Makita DLS110 Instruction Manual
Also see for DLS110: Instruction manualInstruction manualInstruction manualInstruction manualInstruction manual
                                                                                                                                                                                                                                                    | |
31 ENGLISHWIRELESS ACTIVATIONFUNCTIONFor DLS111 onlyWhat you can do with the wirelessactivation function -fortable operation. By connecting a supported vacuumcleaner to the tool, you can run the vacuum cleanerautomatically along with the switch operation of the tool.\Fig.58 -ing items: % % activation function is as follows. Refer to each section for detail procedures.1. Installing the wireless unit2. 3. Starting the wireless activation functionInstalling the wireless unitCAUTION: #/_( @( @QQ# Q& / /@ /&] *@/~#(surface when installing the wireless unit.NOTICE: Clean the dust and dirt on the tool beforeinstalling the wireless unit. Dust or dirt may causemalfunction if it comes into the slot of the wireless unit.NOTICE: To prevent the malfunction caused bystatic, touch a static discharging material, suchas a metal part of the tool, before picking up thewireless unit.NOTICE: When installing the wireless unit, alwaysbe sure that the wireless unit is inserted in the cor-rect direction and the lid is completely closed.1. ] \Fig.59: 1. Lid2. Insert the wireless unit to the slot and then closethe lid.> with the recessed portions on the slot.\Fig.60: 1. Wireless unit 2.$ 3. Lid4. Recessed portionWhen removing the wireless unit, open the lid slowly. = = as you pull up the lid.\Fig.61: 1. Wireless unit 2. Hook 3. Lid% = case or a static-free container.NOTICE: Always use the hooks on the back ofthe lid when removing the wireless unit. If thehooks do not catch the wireless unit, close the lidcompletely and open it slowly again.Tool registration for the vacuumcleanerNOTE:%}= ; registration.NOTE: Finish installing the wireless unit to the toolbefore starting the tool registration.NOTE: During the tool registration, do not pull theswitch trigger or turn on the power switch on thevacuum cleaner.NOTE: Refer to the instruction manual of the vacuumcleaner, too.If you wish to activate the vacuum cleaner along with -tion beforehand.1. Install the batteries to the vacuum cleaner and thetool.2. Set the stand-by switch on the vacuum cleaner to[%K ][ \Fig.62: 1. Stand-by switch3. Press the wireless activation button on the vac-uum cleaner for 3 seconds until the wireless activation = % -vation button on the tool in the same way.\Fig.63: 1. Wireless activation button 2. Wirelessactivation lampIf the vacuum cleaner and the tool are linked success-fully, the wireless activation lamps will light up in greenfor 2 seconds and start blinking in blue.NOTE: = in green after 20 seconds elapsed. Press the wirelessactivation button on the tool while the wireless acti-vation lamp on the cleaner is blinking. If the wirelessactivation lamp does not blink in green, push the wire- < NOTE: When performing two or more tool registra- -tion one by one.Starting the wireless activationfunctionNOTE: Finish the tool registration for the vacuumcleaner prior to the wireless activation.NOTE: Refer to the instruction manual of the vacuumcleaner, too.% vacuum cleaner will automatically runs along with theswitch operation of the tool.1. Install the wireless unit to the tool.2. Connect the hose of the vacuum cleaner with thetool.\Fig.643. Set the stand-by switch on the vacuum cleaner to[%K ][ \Fig.65: 1. Stand-by switch |
Related manuals for Makita DLS110
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
Makita DLS110 Instruction Manual
manualsdatabase
Your AI-powered manual search engine