Nortek 2GIG GC3 Installation And Programming Manual

Also see for 2GIG GC3: User guide User guide Installation and programming guide User guide

Contents

Nortek 2GIG GC3 Installation And Programming Manual Manual pdf 55 page image

Copyright © 2019 Nortek Security & Control LLC 55Choose one of these options:» 30-240 Seconds: Choose a value between 30 and240 seconds.» † ‡ 30 Seconds: For compliance with ANSI/SIA CP-01-2010, the default Entry Delay 1 feature is set to30 seconds.Q6: Entry delay 2, in seconds (30-240)Configures the number of seconds for the Entry Delay 2timer. Different times may be programmed for each SmartAreas. (Smart Areas feature must be enabled (Q69) forvalues for S2-S4 to affect the system) This specifies theamount of time occupants have to disarm the system afterentering the premises through a door. Typically, secondaryentrances that require a slightly longer entry time areprogrammed as an Exit/Entry 2 door. For example, aback, side, or garage entry door. When a user enters thepremises while the system is armed, the Entry Delay 2countdown starts.The GC3 Panel beeps once every two (2) seconds duringthe countdown.Choose one of these options:» 30-240 Seconds: Choose a value between 30 and240 seconds.» †‡ 45 Seconds: For compliance with ANSI/SIA CP-01-2010, the default Entry Delay 2 feature is set to45 seconds.Q7: Remote services providerConfigures the appropriate Remote Services Provider forthe system. A Remote Services Provider is the third-partysecurity provider that powers the system’s interactiveservices.Choose one of these options:» None: Does not specify the provider.» † Alarm.com: Choose this option if the RemoteServices Provider is Alarm.com.Q8: 2-way voiceConfigures the system to automatically turn the GC3Panel’s 2-Way Voice feature ON or OFF after the type ofalarm you specify. This gives the GC3 Panel’s CellularRadio Module the ability to automatically dial theCentral Station and connect with an operator after an alarmsounds. Once connected with the Central Station, peopleon the premises can communicate with the operator usingthe GC3 Panel’s built-in speaker and microphone.Choose one of these options:» Disabled: Turns the feature OFF.» †Stay On Line: Turns the feature ON andautomatically enables the 2-Way Voice feature aftera burglary alarm.» Stay On Line, Including Fire & CO Alarms: Turns thefeature ON and automatically enables the 2-WayVoice feature after a burglary, fire, and/or carbonmonoxide alarm.When the Control Panel connects with the operator, it willbeep once every six seconds. The beep alternates betweentwo tones and indicates the Control Panel is waiting for asession command. If the operator fails to issue a commandwithing three (3) minutes), the call is terminated. Once theoperator presses a command option, the beeps will stopand a three (3)-minute audio session will start.When two (2)-way voice communications have beenestablished, the Central Station operator can use thefollowing telephone keys to control the communications.Each time the operator uses a command key, the sessionis extended for three (3) additional minutes. During the lastminute of communications, the system beeps two (2) timesevery 15 seconds to indicate that time is running out.» Tap 1 to enable Talk mode one (1)-waycommunication from the Central Station to thepremises and allow the operator to talk.» Tap 2 to enable VOX mode two (2)-waycommunications from the Central Station to thepremises.» Tap 3 to enable Listen mode one (1)-waycommunication from the premises to the CentralStation.» Tap 7 to extend the session five (5) minutes withoutchanging the mode of operation.» Tap 9 to end the audio session and terminate thecall.Q9: Disable siren after two-way audioConfigures the system to automatically turn the alarm sirenON or OFF after the end of a 2-Way Voice session. Forthis setting to take effect, “Q8: 2-way voice” above must beenabled.Choose one of these options:» Enabled: Choose this setting if you want the alarmsiren to remain OFF after a 2-Way Voice sessionends.» † Disabled: Choose this setting if you want thealarm siren to resume after a 2-Way Voice sessionends.NOTE: When set to disabled, the alarm siren willonly resume after a 2-way voice session when thecorresponding alarm bell cutoff time has not expired.See “Q40: Burglary bell cutoff time” and “Q41: Firebell cutoff time.”