Notifier AFP-3030 Programming Manual

Also see for AFP-3030: Operation manual Installation manual Operation manual Installation manual

Contents

Notifier AFP-3030 Programming Manual Manual pdf 130 page image

124 AFP-3030 Programming Manual — P/N DOC-01-032:A 26/06/2015Type Codes Type Codes for Input DevicesF.4.3 Type Codes for Monitor ModulesFollowing is a list of monitor module Type Codes, which can be used to change the function of amonitor module point.Type Code Point TypePoint CharacteristicsLatching(Y = yesN = no)ActivatesCBE Device FunctionMONITOR fire alarm Y Y Alarm-monitoring deviceNC MONITOR fire alarm Y Y Alarm monitoring device, where an open circuit = active.MCP fire alarm Y Y Manual fire-alarm-activating deviceSMOKE CONVEN fire alarm Y Y Indicates activation of a conventional smoke detector. An FZM-1must be used for alarm verification of a two-wire conventionaldetector.WATERFLOW fire alarm Y Y Monitor for waterflow alarm switchWATERFLOW S supervisory Y Y Indicates supervisory condition for activated waterflow switchALARM DEV FLT fault N N Used for monitoring audio equipment (use fault zones foractivations)FMM 4-20 user-programmableY Y Monitors 4-20 mA industrial sensors.LATCH SUPERV supervisory Y Y Indicates latching supervisory conditionNC SUP L supervisory Y Y Indicates latching supervisory condition, where an opencircuit = active.TRACK SUPERV supervisory N Y Monitors for waterflow tamper switches for alarm pointsNC SUP T supervisory N Y Indicates tracking supervisory condition, where an opencircuit = active.SPRINKLR SYS supervisory Y Y Monitors a waterflow deviceTAMPER supervisory Y Y Indicates activation of tamper switchACK SWITCH non-alarm N N Performs Acknowledge functionFIRE CONTROL non-alarm N Y Monitors non-fire activationsNON FIRE non-alarm N Y Monitors non-fire activationsNC NON FIRE non-alarm N Y Monitors non-fire activations, where an open circuit = active.POWER MONITR fault* N N Monitors main and auxiliary power supplies (use fault zones foractivations)RESET SWITCH non-alarm N N Performs Reset functionSIL SWITCH non-alarm N N Performs Signal Silence functionDISABLE MON disable N N When this point activates it will create a disable on the panel for thatpoint. No CBE generated. Modules can not be disabled via ACS,Alter Status, or over the network.FAULT MON fault N N Monitors fault inputs (use fault zones for activations)Blank fire alarm Y Y Monitors for a device with no descriptionHEAT DETECT fire alarm Y Y Monitors for conventional heat detectorABORT SWITCH non-alarm N Y Provides an abort function through a monitor module (connected toan abort station) for a releasing zone.MAN RELEASE fire alarm† Y Y Provides a manual release through a monitor module (connected toa pull station) for a releasing zoneMAN REL DELAY fire alarm* Y Y Provides a manual release with a 10-second delay through amonitor module (connected to a pull station) for a releasing zoneSECOND SHOT fire alarm* Y Y Provides a second manual release through a monitor module(connected to a pull station) for a releasing zoneHAZARD ALRT non-fire N Y Monitors for a hazard alertWEATHER ALRT non-fire N Y Monitors for a weather alertPROCESS MON critical process Y Y Monitors for a critical processPROCMON AUTO critical process N Y Monitors for a critical processCO MONITOR CO alarm Y Y Monitors conventional CO detectors for a CO alarm condition.ECS/MN MON alarm Y Y Monitors mass notification devices for alarm activation.ECS/MN SUPT supervisory N Y Tracking supervisory monitor for mass notification devices.ECS/MN SUPL supervisory Y Y Latching supervisory monitor for mass notification devices.ECS/MN TMON fault N Y Fault monitor for mass notification devices.RF GATEWAY non-alarm N Y Provides communication between wireless devices and the firepanelTable F.2 Type Codes for Monitor Modules (1 of 2)