- 41 -Connecting to a Computer1 1. Setup Using EtherTalk(For Mac OS X 10.3.9 to 10.4.11)When connecting to the network with EtherTalk,it is necessary to enable EtherTalk and disablethe sleep mode on the printer. After doing that,install the driver on the computer.Memo● The following procedure uses Mac OS X 10.4.11 as anexample. Depending on an OS, the description may bedifferent. First, enable EtherTalk and disable thesleep mode on the printer.1 Ensure that your printer and thecomputer are turned on and connected.Reference● “Connecting an Ethernet Cable” P.322 Press the <ENTER> button on theoperator panel.3 Press the scroll button several timesto select [Admin Setup], and press the<ENTER> button.䎩䏘䏑䏆䏗䏌䏒䏑䏖䎃䎃䎃䎃䎃䎃䎕䎒䎕䫹 䎦䏄䏏䏌䏅䏕䏄䏗䏌䏒䏑䎤䏇䏐䏌䏑䎃䎶䏈䏗䏘䏓4 Enter the administrator password, usingthe numeric (0-9) keys.The factory default password is “aaaaaa” Pressthe <ENTER> button after each character youinput.䎨䏑䏗䏈䏕䎃䎳䏄䏖䏖䏚䏒䏕䏇䯴䎙䎐䎔䎕䏇䏌䏊䏌䏗䏖䎌5 Press the <ENTER> button.6 Check that [Network Setup] is selectedand press the <ENTER> button.䎤䏇䏐䏌䏑䎃䎶䏈䏗䏘䏓䎃 䎃 䎃䎃䎔䎒䎗䎳䏕䏌䏑䏗䎃䎶䏈䏗䏘䏓䎳䎶䎃䎶䏈䏗䏘䏓䎳䎦䎯䎃䎶䏈䏗䏘䏓䎱䏈䏗䏚䏒䏕䏎䎃䎶䏈䏗䏘䏓7 Press the scroll button several timesto select [EtherTalk], and press the<ENTER> button.䎱䏈䏗䏚䏒䏕䏎䎃䎶䏈䏗䏘䏓䎃䎃䎕䎒䎘䎨䏗䏋䏈䏕䎷䏄䏏䏎䎬䎳䏙䎗䎃 䎤䏇䏇䏕䏈䏖䏖䎶䏘䏅䏑䏈䏗䎃䎰䏄䏖䏎䎬䎳䎃䎤䏇䏇䏕䏈䏖䏖䎃䎶䏈䏗8 Press the scroll button to select[Enable], and press the <ENTER>button.䎨䏗䏋䏈䏕䎷䏄䏏䏎䎃䎃䎃䎃䎃䎃䎃䎔䎒䎔䎧䏌䏖䏄䏅䏏䏈䎍䎃䎃䎨䏑䏄䏅䏏䏈9 Press the <BACK> button until[Network Setup] is displayed.䎱䏈䏗䏚䏒䏕䏎䎃䎶䏈䏗䏘䏓䎃䎃䎕䎒䎘䎨䏗䏋䏈䏕䎷䏄䏏䏎䎬䎳䏙䎗䎃 䎤䏇䏇䏕䏈䏖䏖䎶䏘䏅䏑䏈䏗䎃䎰䏄䏖䏎䎬䎳䎃䎤䏇䏇䏕䏈䏖䏖䎃䎶䏈䏗
