Oki MC860 Maintenance Manual

Also see for MC-860 / CX2633MFP: Service & troubleshooting guide

Contents

Oki MC860 Maintenance Manual Manual pdf 316 page image

Oki Data CONFIDENTIAL43967002TH Rev. 1 316 /7. Troubleshooting7.5.2 TroubleshootingNote! When an attempt is going to be made to replace the PU PCB, be sure to readthe data contents of the EEPROM chip from the old PU PCB beforehand, andcopy the data contents into the new PCB after the new PU PCB is installed.(Refer to 5.4.1 Precautions when replacing the engine control PCB)7.5.2.(1) LCD display error...................................................................................... 317(1-1) LCD does not display anything. ........................................................... 317(1-2) From the startup screen after power-on: ............................................. 318(1-3) Error messages related to Operator Panel are displayed. ................... 3187.5.2.(2) Abnormal operations of printer after the power is turned on .................... 318(2-1) Any operation does not start at all ....................................................... 318(2-2) Abnormal sound is heard..................................................................... 319(2-3) Bad odors are generated. .................................................................... 320(2-4) Rise-up time is slow. ............................................................................ 3207.5.2.(3) Paper feed jam (error 391: 1st tray) ......................................................... 327(3-1) Jam occurs immediately after the power is turned on. (1st tray) ......... 327(3-2) Jam occurs immediately after the paper feed is started. (1st tray) ...... 3277.5.2.(4) Feed jam (error code 380) ....................................................................... 329(4-1) Jam occurs immediately after the power is turned on.......................... 329(4-2) Jam occurs immediately after the paper feed is started. ..................... 3297.5.2.(5) Paper feed jam (error code 390: Multipurpose tray) ................................ 330(5-1) Jam occurs immediately after the power is turned on.(Multipurpose tray) ............................................................................... 330(5-2) Jam occurs immediately after paper feed is started.(Multipurpose tray) ............................................................................... 3317.5.2.(6) Paper running jam (error code 381:.......................................................... 332(6-1) Jam occurs immediately after the power is turned on.......................... 332(6-2) Jam occurs immediately after a paper is taken into printer.................. 332(6-3) Jam occurs in the middle of paper running path. ................................. 333(6-4) Jam occurs immediately after paper has reached the fuser. ............... 3347.5.2.(7) Paper running jam (error code 382) ......................................................... 334(7-1) Jam occurs immediately after the power is turned on.......................... 334(7-2) Paper unloading jam occurs after a paper is taken into printer............ 335(7-3) Paper unloading jam occurs in the middle of paper running path........ 3367.5.2.(8) Two-sided printing jam (error code: 370, 371, 372, 373, 383) ................. 336(8-1) Two-sided printing jam occurs immediately after the power isturned on.............................................................................................. 336(8-2) Two-sided printing jam occurs during taking in the paper intoDuplex unit. .......................................................................................... 337(8-3) Two-sided printing jam occurs in the process of reversing paper. ....... 337(8-4) Two-sided printing jam occurs during transporting paper insidethe Duplex unit. .................................................................................... 338(8-5) Paper is not supplied from the Duplex unit to the regist roller.............. 3387.5.2.(9) Paper size error (error code 400) ............................................................ 338(9-1) Jam occurs when paper end is located near the IN1 sensor. .............. 3387.5.2.(10) ID unit Up/Down error (Service call 140 to 143) ................................... 339(10-1) Error occurs when the ID unit moves down ......................................... 339(10-2) Error occurs when the ID unit moves down ......................................... 3397.5.2.(11) Fuser unit error (error 170 to 177) ........................................................ 340(11-1) Jam occurs immediately after the power is turned on.......................... 340(11-2) Error occurs approx. 1 minutes after the power is turned on. .............. 3407.5.2.(12) Motor fan error (error code 122, 127, 051) ........................................... 341(12-1) The low voltage power supply fan does not rotate immediatelyafter the power is turned on. ................................................................ 341(12-2) Duplex fan does not rotate during the Duplex printing. ........................ 341(12-3) All fans of the printer do not rotate....................................................... 3417.5.2.(13) Print speed is slow. (Performance is low.) ............................................. 341(13-1) Print speed decreases. ........................................................................ 3417.5.2. (14) Option unit cannot be recognized. ......................................................... 342(14-1) Duplex unit cannot be recognized........................................................ 342(14-2) 2nd tray unit cannot be recognized...................................................... 3427.5.2.(15) LED head cannot be recognized. (error code 131, 132, 133, 134) ....... 343(15-1) Service call 131 to 134 (LED HEAD Missing)...................................... 3437.5.2.(16) Toner cartridge cannot be recognized. (Error code 540, 541, 542, 543) ... 343(16-1) Error caused by the consumable items ............................................... 343(16-2) Error caused by the toner sensor ........................................................ 343(16-3) Error caused by the defective mechanism ........................................... 3447.5.2.(17) Fuse cut error (error codes 150 to 155) ................................................. 345(17-1) Fuse cut error ...................................................................................... 3457.5.2.(18) Dew condensation error (Error 123) ...................................................... 345(18-1) Dew condensation error....................................................................... 3457.5.2.(19) Connection diagram ............................................................................... 346