Panasonic AJ-PX5000G Operating Instructions Manual

Also see for AJ-PX5000G: Review Operating instructions Operating instructions

Contents

Panasonic AJ-PX5000G Operating Instructions Manual Manual pdf 156 page image

– 156 –Chapter 7 Menu Operations — Menu list[PROXY SETUP]Item Description of settings Remark[REC MEDIA] Selects media for recording proxy data. f In the following case, proxy data cannot berecorded even if [REC MEDIA] is set to [P2] or[P2&SD].- When the main menu → [REC/PB] → [RECFUNCTION] → [RECORDING] is set to otherthan [NORMAL][P2] Records proxy data to the P2 card.[P2&SD] Records proxy data to both the P2 card and SD memory card.[OFF] Does not record proxy data.[REC MODE (HD)] Sets the recording mode of proxy data. (in the HD mode only)[STD 2CH MP4], [LOW 2CH MOV], [HQ 2CH MOV], [HQ 4CH MOV], [SHQ 2CHMOV][TC SUPER] Sets whether to superimpose time code display on the proxy data recordedimages.[UPPER] Superimposes the time code display at the top of the recordedimages.[LOWER] Superimposes the time code display at the bottom of therecorded images.[OFF] Does not superimpose time code on recorded images.[PROXY DISP] Selects whether to display proxy data recorded information or messages in theviewfinder and LCD monitor.f This can also be set in the main menu → [VF] →[VF INDICATOR] → [PROXY DISP].[ON] Displays proxy recording information and SD memory cardremaining capacity at the start of recording.Warning information is displayed at all times.[OFF] Displays proxy and SD memory card warning information foronly three seconds when warning occurs.are factory settings.[TC/UB]Item Description of settings Remark[UBG MODE] Selects the user bits mode.[USER] Selects the user bits value set in the display window.[TIME] Selects the local time. (hh, mm, ss)[DATE] Selects the local date and time. (YY, MM, DD, hh)[EXT] Records the user bits values currently entered to the terminal.[TCG] The [TCG] value is entered to the user bits.[FRAME RATE] Selects camera imaging information (such as frame rate).[REGEN] Reads the value recorded to the card and continuously recordsthat value.[VITC UBG MODE] Selects the VITC user bits mode.[USER/EXT] If [UBG MODE] is operating in [EXT], that value is followed andwhen not [EXT], a user value set in [USER] is recorded.[TIME] Selects the local time. (hh, mm, ss)[DATE] Selects the local date and time. (YY, MM, DD, hh)[TCG] The time code generator value is entered to the user bits.[FRAME RATE] Selects camera imaging information (such as frame rate).[REGEN] Reads the value recorded to the card and continuously recordsthat value.[DF MODE] Sets drop frame mode/non-drop frame mode of the [CTL] and [TCG].[DF] Uses the drop frame mode.[NDF] Uses the non-drop frame mode.[TCG SET HOLD] If the internal time code generator is set with the switch before turningpower off, switch [ON]/[OFF] for the function that recording starts from the presetvalue when turning on the power to start recording.[ON], [OFF][FIRST REC TC] Selects whether to regenerate the time code to the value on the P2 card at thefirst recording after power is turned on, a P2 card is inserted, or the P2 cardtargeted for recording is switched.f Make sure the date and time are correctly set. Forthe setting method, refer to “Setting the date/timeof the internal clock” (page 30).[PRESET] Uses the internal time code of the camera.[REGEN] Regeneration is performed for the time code of the clip withthe newest date and time of the clips recorded to the P2 cardtargeted for recording.[TC OUT] Selects the time code output to the terminal.[TCG] Outputs the time code generator value at all times.[TCG/TCR] Outputs the time code generator value during recording and thetime code reader value during playback.are factory settings.