Panasonic AJ-PX5000G Operating Instructions Manual

Also see for AJ-PX5000G: Review Operating instructions Operating instructions

Contents

Panasonic AJ-PX5000G Operating Instructions Manual Manual pdf 196 page image

– 196 –Chapter 9 Maintenance and Inspection — Warning systemWarning content There is an error in the fan and it stops. Otherwise [OPTION MENU] → [OPTION] → [FAN MODE] → [OFF] has beenset.Recording or playback operation Operation will continue, but if the camera is operated with the fan stopped, the temperature rises and recording/playbackmay not operate normally.Action to takeIf the fan has stopped with error, stop using immediately and consult your dealer.If the fan has stopped, temperature of the camera will rise. Therefore, do not use the camera for a long period of time.Use the tripod, etc., and do not touch the camera directly.Error codeIf errors occur on the camera for any cause, the following error code is displayed on the time code display in the display window. Check the types ofwarning, and deal with the error according to “Warnings description list” (page 194).Code No. Message display Description Type of warningFirst row Second row[E-30] [TURN POWER OFF] [P2 CARD] P2 card removal error 3 Card removal error[E-31] [TURN POWER OFF] [SYSTEM MODE] System mode error 2 Mismatched format[E-33] [SYSTEM ERROR] [CAMERA] Camera unit error 1 System error[E-34] [SYSTEM ERROR] [LCD MICON] LCD microcomputer error 1 System error[E-35] [SYSTEM ERROR] [CODEC] Codec control error 1 System error[E-36] [SYSTEM ERROR] [P2 SYSTEM] P2 system error 1 System error[E-37] [SYSTEM ERROR] [P2CS] P2CS microcomputer error 1 System error[E-39] [SYSTEM ERROR] [INITIALIZE] Video initialization error 1 System error[E-63] No display No display System control microcomputer error 1 System error[E-64] [SYSTEM ERROR]or no display[FRAME SIGNAL]or no display Standard signal error 1 System errorWarning information displayMonitor display Description Camera operationFirst row Second row[AUTH NG CARD] (slotnumber) NoneCPS authentication of microP2 memory card has failed. The microP2memory card with CPS authentication failed cannot be recorded orplayed back. Select [AUTHENTICATE] in the main menu → [CLIP],and enter the password.Continue[BACKUP BATT EMPTY] NoneDisplays any reduced voltage detected on the backup battery in theinternal clock when the power is turned on.Follow “Charging the built-in battery” (page 193) to charge thebattery.Continue[CARD ERROR] (slotnumber) NoneDisplayed when an data error caused by the P2 card occurs duringrecording.Displayed after recording stops until the next operation. Alsodisplayed for three seconds during playback when a P2 card errorcauses playback to stop.Replace the P2 card of the slot where the error occurred.Stop[DIR NG CARD] (slotnumber) None The directory position is not correct. Make a card backup immediatelyand use again after formatting. Continue[FAN STOPPED] NoneDisplayed when the fan motor stops.The camera operates even if the fan stops. Refrain from usingimmediately.Continue[PB INTERMITTENT](slot number) NonePlayback is interrupted on the SDHC/SDXC memory card. A cardwhose playback performance cannot be assured is inserted. Use ofmicroP2 or P2 memory card is recommended.Continue[PROXY ERROR] NoneProxy errorFor details, refer to “Error displays about proxy data recordings”(page 43).Continue[PROXY RECWARNING] NoneProxy errorFor details, refer to “Error displays about proxy data recordings”(page 43).Continue[REC IMPOSSIBLE] (slotnumber) NoneAn SDHC/SDXC memory card is inserted into the microP2 memorycard slot.Recording to the SDHC/SDXC memory card is disabled. Record tomicroP2 or P2 memory cards.Continue[REC WARNING] [FRAME SIGNAL]Displayed when a video or audio error occurs during recording. Turnthe power off and on before using it again.When input signals are disrupted, recording continues while disruptedimages are recorded. Check the signal to be input to the camera.Continue[REC WARNING] [OVER MAX# CLIPS]Displayed when attempting to record in excess of the maximum totalnumber of clips allowed for one P2 card.Replace the P2 card or delete unnecessary clips.Stop