|
– 64 –Chapter 4 Adjustments and Settings for Recording — Setting the time data@@ NOTEt Thumbnail operations and menu operations on thumbnail operation section are not possible while the switch is set to .t To confirm VITC UB, press the switch to display [VTCG] on the display window.Retention of user bits in memoryUser bit settings are automatically recorded and are retained even if the power is turned off.Setting the time code1 Set the switch to .2 Set the switch to .3 Set [DF] or [NDF] in the main menu → [REC/PB] → [TC/UB] → [DF MODE].For details, refer to “Setting menu basic operations” (page 134).f Set [DF] to advance the time code in the drop frame mode, and set [NDF] to advance it in the non-drop frame mode.4 Set the time code by the cursor buttons.f Screen display- I: The digit to be set (flashing) moves to the right.- Y: The digit to be set (flashing) moves to the left.- `: The value of the digit to set (flashing) is incremented by one.- {: The value of the digit to set (flashing) is decremented by one.5 Switch by the switch.To advance the time code by free run, switch to -RUN>, and to advance by recording run, switch to -RUN>.Settable time code rangeFor 59.94 Hz (except for 24PN) 00:00:00:00 - 23:59:59:29For 50 Hz: 00:00:00:00 - 23:59:59:24@@ NOTEt Switching of [DF] and [NDF] is enabled when the system frequency of the camera is set to 59.94 Hz.t Thumbnail operations and menu operations on thumbnail operation section are not possible while the switch is set to .Time code regenerationWhen the switch is set to -RUN>, the time code currently recorded to the last frame of the last clip (clip with the newest recording date andtime) recorded to the P2 card can be read and recorded. If the P2 card is removed or inserted or a card to be recorded is changed by the [SLOT SEL]function of the button while [REGEN] is selected in the main menu → [REC/PB] → [TC/UB] → [FIRST REC TC], the time code is carried overand recorded to the clip last recorded on the P2 card that was to be recorded to. If there are no recorded clips, the time code is recorded from the TCgenerator value on the camera.Regeneration by the recording check functionWhen [PRESET] is set in the main menu → [REC/PB] → [TC/UB] → [FIRST REC TC], or after the time code is set or reset, or the time code is switchedfrom free run to recording run, the time code can be regenerated to the last time code of the clip recorded to the P2 card. To perform this operation, set[REC CHECK] in the main menu → [CAMERA] → [SW MODE] → [RET SW], and set [ON] in the main menu → [REC/PB] → [TC/UB] → [REC CHECKREGEN], respectively.1 Check the P2 card to be recorded to.To regenerate to the time code of the last recorded clip when multiple P2 cards are inserted, press the button to display thethumbnail screen.2 Check the P2 card recorded with the clip displayed last on screen, and switch the slot by the button assigned with[SLOT SEL] so that recording is performed on that P2 card.3 Press the button on the lens.f [TC REGEN] is displayed on the viewfinder.f When recording is next performed, the time code is regenerated to the last recorded clip on the card to record to.@@ NOTEt When the card to record to is changed, the time code is regenerated to the time code of the last recorded clip on the P2 card that was changed to.t During recording or free run, this function cannot be used.Time code function during battery replacementEven during battery replacement, the backup mechanism functions, allowing the time code generator to continue operating.When each item of the system mode has been changed, the time code of free run may shift. Turn on the power again, check the time code, and reset it,if necessary.@@ NOTEt When the switch has been switched to → → , the backup accuracy of the time code in the free run mode isapproximately ±2 frames.
|
