|
93Setup menus (continued)The cumulative total standby time passed in the samelocation increases at such times when the same material isrepeatedly used as is the case when programs aretransmitted, for example.To protect the tape, it is recommended to set the standbytime at the same position as short as possible.The underlining (__) denotes the factory setting mode.No./Item Description of setting400STILL TIMERFor selecting the duration of the time takenafter the VTR is left standing in the STOP orsearch STILL mode (JOG, SLOW or SHTL)before the tape protection mode is established.(Units: s = seconds, min = minutes)0000 0.5s0001 5s0002 10s0003 20s0004 30s0005 40s0006 50s0007 1min0008 2minWhen a DV or DVCAM tape is used, the time is setto 10 seconds even when a setting of 2 (10s) orlonger is selected.401SRCPROTECTWhen the time set in Setup Menu No. 400 (STILLTIMER) elapses in the Search Still (JOG/SLOW/SHTL) state, the unit automatically returns tothe tape protection mode. This is for selectingthe types of tape protection mode.0000 STEPSTEP FWD0001 HALFHalf-loading0002 T-RELTension releasez When STEP FWD is selected, the VTR isautomatically transferred to the standby OFF(half-loading) mode after it has been left standingin the STILL status for a total of 30 minutes (or 1minute in the case of a DV or DVCAM tape).z When, after tension release has been selectedand the VTR has been transferred to the tensionrelease mode, the VTR has been left standing inthis mode for a total of 2 hours, it is automaticallytransferred to the standby OFF (half-loading)mode. However, in the case of a DV or DVCAMtape, the transfer to the tension release mode isinhibited, and the VTR operates as if STEP FWDhas been selected.z For an unused tape (except for a DV/DVCAMtape), the mode forcibly moves to the tensionrelease mode 0.5 seconds after the STILL state.402DRUM STDBYFor selecting whether the drum is to operate inthe standby OFF (half-loading) mode.0000 OFFThe drum stops rotating.0001 ONThe drum continues to rotate.No./Item Description of setting403STOPPROTECTWhen the time set in Setup Menu No. 400 (STILLTIMER) elapses in the STOP state, the unitautomatically returns to the tape protectionmode. This is for selecting the types of tapeprotection mode.0000 STEPSTEP FWD0001 HALFHalf-loading0002 T-RELTension releasez When STEP FWD is selected, the VTR isautomatically transferred to the standby OFF(half-loading) mode after it has been left standingin the STOP mode for a total of 30 minutes (or 1minute in the case of a DV or DVCAM tape).z When, after tension release has been selectedand the VTR has been transferred to the tensionrelease mode, the VTR has been left standing inthis mode for a total of 2 hours, it is automaticallytransferred to the standby OFF (half-loading)mode. However, in the case of a DV or DVCAMtape, the transfer to the tension release mode isinhibited, and the VTR operates as if STEP FWDhas been selected.z For an unused tape (except for a DV/DVCAMtape), the mode forcibly moves to the tensionrelease mode 0.5 seconds after the STILL state.z For the DVCPRO HD-SP, DVCPRO50, orDVCPRO tapes, the mode forcibly moves to thetension release mode 0.5 seconds after theSTILL state during the EE mode.
|
