Panasonic DVCPRO HD AJ-HD1800P Operating Instructions Manual

Also see for DVCPRO HD AJ-HD1800E: Parts list

Contents

Panasonic DVCPRO HD AJ-HD1800P Operating Instructions Manual Manual pdf 94 page image

94Setup menus (continued)*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz(HD, SD) mode is selected in System Menu No. 25 (SYSTEMFREQ), this item is not displayed.*2 When the 23/24 Hz mode, 25 Hz (HD) mode, or 50 Hz (HD)mode is selected in System Menu No. 25 (SYSTEM FREQ),this item is not displayed.The underlining (__) denotes the factory setting mode.No./Item Description of setting500* 2VITC BLANKFor selecting whether or not to output the VITCsignal at the positions selected by setup menuitems No.501 (VITC POS-1) and No.502 (VITCPOS-2).0000 BLANKThe VITC signal is not output.0001 THRUThe VITC signal is output.Only the SD output takes effect at this setting.501* 2VITC POS-1For setting the position where the VITC signalis to be inserted.<59/60Hz> <50Hz>, <25Hz(SD)>, <50Hz(SD)>0000 10L: :0006 16L: :0010 20L0000 7L: :0004 11L: :0015 22Lz The same line as the one selected by the setupmenu item No.502 (VITC POS-2) orNo.692(UMID POS) cannot be selected.z Only the SD output takes effect at this setting.502* 2VITC POS-2For setting the position where the VITC signalis to be inserted.<59/60Hz> <50Hz>, <25Hz(SD)>, <50Hz(SD)>0000 10L: :0008 18L: :0010 20L0000 7L: :0006 13L: :0015 22Lz The same line as the one selected by the setupmenu item No.501 (VITC POS-1) orNo.692(UMID POS) cannot be selected.z Only the SD output takes effect at this setting.503* 1TCG MODEFor setting the synchronization of the internaltime code generator.0000 REGENThe time code reader is synchronized with thetime code which is read from the tape.0001 PREPresetting is enabled at the operation panel or bythe remote controller.0002 AUTOThe REGEN and PRE settings are automaticallyswitched in accordance with the operation mode.In the editing mode: REGEN is selected.In all other modes: PRE is selected.504* 1RUN MODEFor setting when the internal time codegenerator is to advance depending on theoperation mode.0000 RECThe time code generator is advanced duringrecording.0001 FREEThe time code generator is advanced while thepower is on regardless of which operation modeis established.No./Item Description of setting505*1TCG REGENFor selecting the regeneration signal whenREGEN has been selected as the TCG (timecode generator) mode.0000 TC&UBRegeneration applies to both the time code anduser bits.0001 TCRegeneration applies only to the time code only.0002 UBRegeneration applies only to the user bits only506*1REGEN MODEFor selecting the editing mode range when theVTR is operating in the REGEN mode whileperforming editing operations with “AUTO”selected as the setup menu item No.503 (TCGMODE) setting.0000 AS&INRegeneration applies during assemble or insertediting.0001 ASSEMRegeneration applies during assemble editing.0002 INSRTRegeneration applies during insert editing507*1TC SOURCEFor selecting the time code to be used whenHDSDI or SDSDI has been selected as the setupmenu item No.600 (VIDEO IN SEL) setting whenan external time code is to be used.[When HDSDI has been selected]0000 INTThe time code of the internal time code genera-tor is used.0001 EXT_LLTC of the TIME CODE IN connector is used.0002 SLTCThe LTC information added to the serial signalswhich are input to HD SDI IN is used.0003 SVITCThe VITC information added to the serial signalswhich are input to HD SDI IN is used.[When SDSDI has been selected]0000 INTThe time code of the internal time code genera-tor is used.0001 EXT_LLTC of the TIME CODE IN connector is used.0002 VITCThe VITC information added to the serial signalswhich are input to SD SDI IN is used.z If the VIDEO IN SEL input selection is changed,the time code is converted as shown below.[HDSDI] <> [SDSDI]INT <> INTEXT_L <> EXT_LSLTC <> EXT_LSVITC <> VITCz When [1394] is selected in Setup Menu No. 600(VIDEO IN SEL), the time code input for theIEEE 1394 digital input/output connector is used.However, the VITC information is notsuperimposed on the video signal during EEmode and when recording. Furthermore, LTCinformation and VITC information are notsuperimposed on the HD serial output.