Panasonic MINAS-BL GP series Instructions Manual

Also see for MINAS-BL GP series: Technical instructions Technical instructions Manual

Contents

－ 95 －－ 94 －Conformance to EC directive and UL standard• DV0P4190• DV0P1450Circuit diagram1ø4.2±0.241±1UL-1015 AWG1628±15.5±111±128.5±14.5±0.5200 +30−02 3[Unit: mm]Circuit diagramø4.2±0.241±1UL-1015 AWG1628±15.5±111±128.5±14.5±0.5200 +30−01 2[Unit: mm]Recommended circuit breaker (MCCB)Made by Sensata Technologies Japan Limited:Type IELH-1-11-63-5A-M (single phase) Type IELH-1-111-63-5A-M (3-phase)(Rated current 5A, cutoff characteristics DELAY63)• Recommended cutoff characteristics: DELAY61-63Surge absorberNoise filter for control signals39±134±130±113±1mass: 62.8g[Unit: mm]• DV0P1460Specifications• Brushless motor specificationsItem SpecificationsFlange size 80 mm sq. 90 mm sq.Motor model No. MBMU5AZAB MBMU9A1AB MBMU9A2AB MBMU1E1AB MBMU1E2ABMotor rated output (W) 50 90 130Voltage for 100 V/200 V for 100 V for 200 V for 100 V for 200 VRated torque (N･m) 0.16 0.29 0.41Starting torque *1(N･m) 0.24 0.43 0.62Rated input current(A(rms)) 0.53 0.53 1.00 0.50 1.30 0.72Moment of inertia ofrotor（×10−4 kg･m 2） 0.12 0.27 0.36Rating ContinuousRated rotation speed *2（r/min） 3000maximum rotationspeed（r/min） 4000Speed control range(r/min) 30 to 4000Axial runout 0.05 mm or less at the position of 3 mm from the shaft endBearing Ball bearingInsulation resistance Measure the insulation resistance with 500 V Megger. It must be above 20 MΩMeasuring position: Between power input line (L1, L2,L3) and grounding wireIsolation voltage 1500 VAC, 1 minute, 10 mA or less (between power and grounding wire)Ambient temperature −10 ℃ to +40 ℃ (free from freezing)* Ambient temperature is measured at a distance of 5 cm from the motor.Ambient humidity 20 to 85% RH (free from condensation)Altitude Lower than 1000mVibration 4.9 m/s 2 or less (10 to 60 Hz) X, Y, ZImpact Lower than 98m/s2Motor insulation class 130(B) (UL certified 105 (A))Storage temperature –20˚C to 60˚C ( free from condensation)*Extreme temperatures are permissible only for short period such as during transportation.Storage humidity 85%RH or below (free from condensation)Protection structure IP65*3Number of poles 8Motor mass (kg) 0.7 1.0 1.2*1 Representative value*2 Motor shaft speed: to be multiplied by the reduction ratio when the gear head is used.*3 Excluding the shaft pass-through section and cable end connector.* Should conform to the test conditions specified in EN standard (EN60529 and EN60034-5).Not suitable for application where watertightness is required over a prolonged period, even iffrequently washed.• Standard characteristics measurement conditions are temperature of 25 °C and relative humidity of65%, and may be extended to 5 to 35 °C and 45 to 85% RH.