– 107 –Chapter 10 Menu Operations — Menu listItem Description of settings[- NEAR END VOLT] Sets the near end voltage when the remaining charge of the battery for the V-RAW recorder is detectedwith the voltage level.Displayed only when the V-RAW recorder is connected.[11.0V] - [15.0V] (0.1 V step)f Factory setting: [13.2V][- END VOLT] Sets the end voltage when the remaining charge of the battery for the V-RAW recorder is detected with thevoltage level.Displayed only when the V-RAW recorder is connected.[11.0V] - [15.0V] (0.1 V step)f Factory setting: [12.5V][CAM DC IN SOURCE] Sets the type of the external power source input to the terminal of the camera extension modulewhen the camera module and the recording module is separated and they are used connected with anextension cable.Displayed only when the extension module is attached.[DC POWER SUPPLY]: Selected when connecting an AC adaptor. In this case, the remaining batterycharge level is not displayed.[BATTERY]: Selected when a battery is connected to the terminal. The remaining battery level ofthe camera extension module is detected in accordance with [CAM BATT FULL], [CAM BATT NEAR END],or [CAM BATT END].f Factory setting: [DC POWER SUPPLY][CAM BATTERYSETTINGS](Display only)[- FULL VOLT] Sets the voltage to display the remaining battery level of the camera extension module as full when thecamera module and the recording module is separated and used by connecting them with a extensioncable.Displayed only when the extension module is attached.[13.0V] - [17.0V] (0.1 V step)f Factory setting: [15.5V][- NEAR END VOLT] Sets the near end voltage for the remaining battery level of the camera extension module when thecamera module and the recording module is separated and used by connecting them with a extensioncable.Displayed only when the extension module is attached.[11.0V] - [15.0V] (0.1 V step)f The maximum value is the value set in [FULL Volt]. (However, the maximum is [15.0V])f Factory setting: [13.2V][- END VOLT] Sets the end voltage for the remaining battery level of the camera extension module when the cameramodule and the recording module is separated and used by connecting them with a extension cable.Displayed only when the extension module is attached.[11.0V] - [15.0V] (0.1 V step)f The maximum value is the value set in [NEAR END Volt].f Factory setting: [12.5V][END ALARM] Sets whether to sound an alarm at battery remaining charge level end.[ON], [OFF]f Factory setting: [ON][FAN] [FAN SPEED] Select the rotation speed of the fan.[REC AUTO]: The rotation speed is lowered simultaneously with start of recording. However, the fan willrotate in maximum speed when it reaches the specified temperature.[MATCH CODEC]: The fan will operate in rotation speed appropriate for each in accordance with [MAINCODEC].[ALWAYS FULL]: The fan will always rotate at the maximum speed.f Factory setting: [REC AUTO][GENLOCK] [GENLOCK MODE] Switches the synchronization signal of the camera signal.[INT]: Synchronizes to the internal standard signal.[EXT]: Synchronizes to the entered external standard signal.f Factory setting: [INT][H PHASE COARSE] Roughly adjusts to match horizontal synchronization phase when building a system.[−100]…[100]f Factory setting: [0][H PHASE FINE] Minutely adjusts to match horizontal synchronization phase when building a system.[−100]…[100]f Factory setting: [0][SENSOR SYNCHRO] Sets the operation to synchronize the sensors for creating 3D video, etc.[MASTER]: Outputs with the synchronization signal superimposed to the output from the terminal.[SLAVE]: Shoots with the sensor synchronized to the synchronization signal from the master. It isnecessary to set [GENLOCK MODE] to [EXT] to perform slave operation. The synchronization signal isoutput from .[OFF]: Output or receiving of the synchronization signal is not performed.f Factory setting: [OFF][CONTROL DISPLAY] [BRIGHTNESS] Adjusts the brightness of the control panel.[−15]…[15]f Factory setting: [0][COLOR LEVEL] Adjusts the color levels of the control panel.[−15]…[15]f Factory setting: [0]
