Parker SciLog FilterTec Plus Installation, Operation & Maintenance Instructions Manual

Contents

Parker SciLog FilterTec Plus Installation, Operation & Maintenance Instructions Manual Manual pdf 9 page image

9FilterTec Plus System Specifications:Mechanical: Dimensions: Width: 5.75 in (14.6cm); Height: 8.5 in (212.6); Depth: 11in (27.9) Weight: 14 lbs (6.4kg) Enclosure: Aluminum / Steel; Corrosion Resistant, Recessible Handle Pump Head / Motor Options: Three Masterflex Easy-Load II (77201-60) adjustable occlusion pump heads with 8RPM motor, accommodates thin-walled (0.060”) pump tubing: #13, 14, 16, 25, and #17.Pump Rate Range: 0.03 to 24.3 ml/min. Three Masterflex Easy-Load II (77201-60) adjustable occlusion pump heads with 160-RPM motor, accommodates thin-walled (0.060”) pump tubing: #13, 14, 16, 25, and #17.Pump Rate Range: 0.5 to 554 ml/min. Three Masterflex Easy-Load II (77201-62) adjustable occlusion pump heads with 600-RPM motor, accommodates thick-walled (0.090”) pump tubing: #15, 24 and #35. PumpRate Range: 59 to 2,258 ml/min. Pressure Sensors: Accommodates up to three (3) SciPres ™ Disposable pressuresensors: P1, P2, and P3. Pressure control is achieved by modulating pump output. Theuser selects P1, P2 or P3 as the controlled pressure. Pressure Displayed with a resolution of 0.1 psi; choice of bar, psi, kpa. Pressure Range: The default pressure range of the sensors is 0-60psi, and is calibrated atthe factory. Most peristaltic pumps generate pressures up to 40 psi. If you have need forhigher pressures, contact Parker Customer Service for assistance.Electrical : Power: 90 - 264 V , 47-63 Hz, 150 VA, listed Class 2 switching power supply; doublefused: 1A-T, 250V (CE: IR35A 250V ). Battery: CR1220, used to support the internal clock only, not user serviceable. Motor: Choice of three (3) motors: 8, 160 and 600 RPM at 30V , 3.8 Amperes, VariablePump Speed optically encoded, servo-controlled motors. Encoder: 100 lines/rev for 600-RPM motor. 120 lines per/rev for 8 & 160-RPM motors. I/O Ports: “Printer”, Female DB9 connector for data collection with Printer or PC. “S1”, “S2”, “S3”, Male DB9 connector for RS-232 connections to an electronic scale. “External I/O”, Female DB37 connector used for remote On/Off control of FilterTec Plus viafootswitch, or for Analog interface with 4-20 ma sources, A1, A2, A3. “V”, Female DB15 connector, Not utilized on FilterTec Plus. “Temperature”, 2 pin Conxall connector for SciTemp™ disposable Temperature Sensor. “P1, P2, P3”, RJ11 connectors used for SciPres disposable Pressure Sensors. “USB”, USB-A connector, used for RS-232 data collection with a PC. “Ethernet”, RJ-45 connector, not enabled. Display: Two-line LCD, 20 characters each, back-lit. Data Entry: Membrane keyboard with auditory feedback.Environmental : Temperature range: 4 to 40 C. Altitude: up to 2000 Meters Indoor, dry environments only, clean-up is wipe down only.(IP 20) Relative humidity: 0-95% Voltage fluctuations +/- 10% Pollution degree: 2