Regency P33E-NG4 Owners & Installation Manual

Contents

Regency P33E-NG4 Owners & Installation Manual Manual pdf 8 page image

8 Regency® P33E-4 Zero Clearance Direct Vent Gas FireplaceINSTALLATIONDUCT SYSTEM OPTIONKit #946-556The HeatWave Air Duct Kit increases theeffectiveness of your fireplace by dispersing warmair from the fireplace to remote locations in the sameroom or other rooms in your home.Up to two kits may be installed on the fireplace.Please Note: Only 1 HeatWave kit may be oper-ated at one time. This includes the internal bloweroption as well.INSTALLATIONCHECKLIST1) Locate appliancea) Room location(Refer to "Locating Your Fireplace" Section)b) Clearances to Combustibles(Refer to "Clearances" Section)c) Mantle Clearances(Refer to "Combustible Mantels" Section)d) Framing & Finishing Requirements (Referto "Framing & Finishing" Section)e) Venting Requirements(Refer to "Venting" Sections)2) Assemble Top Facing Support and SideNailing Strips (Refer to "Unit Assembly Priorto Installation" Section). NOTE: Must be donebefore installing unit into fireplace.3) Install vent (Refer to "Venting" Sections)4) Make gas and electrical connections. Test thepilot. Must be as per diagram.(Refer to "Gas Line Installation" and "PilotAdjustment" Section).Convert to Propane if desired.(Refer to "Conversion Kit from NG to LPG"Section).5) Install 4-AA batteries into the battery pack.Batteries must be installed to operate the burnerswitch.6) Install standard and optional features. Refer tothe following sections:a. Optional Brick Panelsb. Log Set Installationc. Standard Flush Doord. Optional Flush Trime. Double Screen Doorf. Optional Bay Doorg. Optional Bay Trimh. Flush Louversi. Bay Louversj. Full Screen Doorsk. Optional Contemporary Faceplatel. Optional Wall Thermostatm. Optional Remote Controln. Optional Wall Switcho. Installing the Optional Fan7) Final check.Diagram 1Before leaving this unit with the customer, theinstaller must ensure that the appliance is firingcorrectly and operation fully explained tocustomer.This includes:1) Clocking the appliance to ensure the correctfiring rate (rate noted on label) after burningappliance for 15 minutes.2) If required, adjusting the primary air to ensurethat the flame does not carbon. First allow theunit to burn for 15-20 min. to stabilize.CAUTION: Any alteration to the product thatcauses sooting or carboning that resultsin damage is not the responsibility of themanufacturer.LOCATING YOURFIREPLACE1) When selecting a location for your fireplace,ensure that the clearances outlined on thispage are met.2) Provide adequate clearances for servicing.3) The appliance must be installed on a flat,solid, continuous surface (e.g. wood, metal,concrete). This may be the floor, or raised upon a platform to enhance its visual impact.If the appliance is going to be installed oncarpeting, combustible linoleum tile or othercombustible material other than wood flooring,the appliance must be installed on a metal orwood panel extending the full width and depthof the appliance.4) The P33E-4 can be installed in a recessedposition or framed out into the room as in A,B, C, D. See Diagram 1 below.5) This appliance is Listed for bedroominstallations when used with a Listed MillivoltThermostat. Some areas may have furtherrequirements, check local codes beforeinstallation.6) The P33E-4 Direct Vent Gas Fireplace isapproved for alcove installations, which meet theclearances listed on the "Clearances" Section.7) We recommend that you plan your installation onpaper using exact measurements for clearancesand floor protection before actually installing thisappliance. Have a qualified inspector, dealer, orinstaller review your plans before installation.Note: For vent terminations see "Exterior VentTermination Locations" Section.A) Flat on WallB) Flat on Wall CornerC) Recessed into Wall/AlcoveD) Corner