49APRS Set mode function list 1 APRS AF DUALSound setting for AF Dual FunctionSetting Item: ON / OFFDefault: OFFExplanation:ON/OFF setting to enable the AF Dual function while APRS function is active. 2 APRS DESTINATIONModel Code DisplaySetting Item: [APY01D]Default: [APY01D]Explanation:Displays the model code. This setting cannot be changed. 3 APRS FILTERFilter function settingSetting Item: Mic-E / POSITION / WEATHER / OBJECT / ITEM / STATUS / OTHER /ALTNETDefault: Mic-E: ON / POSITION: ONWEATHER: ON / OBJECT: ONITEM: ON / STATUS: ONOTHER: OFFALTNET: OFFExplanation:For setting FILTER for obtaining various beacon types.ON: Obtains beaconsOFF: Does not obtain beaconsMic-E: Displays the obtained MIC-Encoder beaconsPOSITION: Displays the obtained Position of beaconsWEATHER: Displays the obtained Weather beaconsOBJECT: Displays the obtained Object of beaconsITEM: Displays the obtained item of beaconsSTATUS: Displays the obtained Status of beaconsOTHER: Displays the obtained packets other than those used in APRS.ALTNET: Displays the obtained packets specified by Destination Address in AlternateNets. 4 APRS MODEMAPRS baud rate settingsSetting Item: OFF / 1200bps / 9600bpsDefault: OFF

instruction manual

Initial Setup Procedure for APRS Operation

Operating APRS using the GPS function

Setting the Callsign of Your Station

Setting APRS baud rate

Setting the Symbol of Your Station

Setting the operating frequency for APRS

Description of APRS beacon screen and key operation

Notification of beacons or messages with a popup screen APRS POPUP Function

Screen when BND2s to BND60s is selected

Notification of beacon or message reception with a ringer sound APRS RINGER Function

Displaying RAW packet data

Deleting beacon stations from the list

Set the automatic transmission interval for sending a beacon

Status Text Register

Select a Position Comment

Setting the Digipter Route

APRS message screen and key operation

Reception/Transmission Details Screen and Key Operation

Message Editing Screen and Key Operation

Receiving Messages

Receive message filter settings

Deleting messages from the list

Message creation and transmission

APRS Set Mode List

APRS Set mode function list

Yaesu FT1DR Instruction Manual

Introduction

How to Read This Manual

Safety Precautions (Be Sure to Read)

Before Transmitting Radio Waves

Names and Functions of Controls

Basic Operation

Attaching a Hand Strap

Charging the Battery Pack

Connecting an External Power Supply for Use in Vehicle (USA/EXP version only)

Using a microSD memory card

Formatting a microSD memory card

Performing Communication

Adjusting the Volume Level

Selecting an Operating Band

Selecting a Frequency Band

Tuning in to a Frequency

Selecting Communication Mode

Listening to the Radio

Miscellaneous Settings

Muting Audio

Changing the Transmission Power Level

Adjusting the Squelch Level

Changing the Mode Manually

Locking keys and switches

Repeater Operation

Repeater Shift

Using the Memory

Registering to Memory Channel

Split Memory

Recalling Home Channel

Deleting Memory Channel

Assigning a Name to a Memory Channel

Using Memory Bank

Recalling Memory Bank

Convenient Preset Receiver Memory Channels

Recalling Preset Receiver Memory Channel to Listen to the International VHF (Marine) Radio

Recalling Preset Receiver Memory Channel to Listen to the World Broadcast

Scanning Function

Canceling Scanning

Specifying the Frequency You Do Not Want to Scan

Selecting a Reception Method When Scanning Stops

Specifying a Skip/Selected Memory Channel

Scanning Only the Selected Memory Channel

Memory Bank Link Scan

Programmable Memory Channel Scan (PMS)

Performing Programmable Memory Channel Scan

What is the GM function

Using the APRS Function

Using the GPS Function

Method of Positioning by GPS

Saving GPS Information (GPS Log Function)

Explanation of GPS Screen and Operation

Smart Navigation Function

Description of the BACK TRACK Function Screen

Convenient Functions

Home Channel Dual Reception Home channel Priority memory channel

reception over the other frequency while listening to the radio

setting the resumption time of radio reception

Using the DTMF Function

Confirming the entered DTMF code by the sound

Sending a DTMF Code Manually

Searching for signals with the signal strength graph Band Scope Function

Communicating with a Specific Remote Station

Selecting a Tone Frequency

Searching for the Frequency of the Tone Squelch Used by the Remote Station

Used by the Remote Station

Notification of Call from the Remote Station by Vibration of the Vibrator

Notification of a Call from a Remote Station by the Bell

Flow of Operation to Use the Pager Function

Setting the Code of Your Station

Calling a Specific Station

being called by the remote station (standby operation)

Functions Used As Needed

Set Mode Option List

Displaying the GPS screen

Setting the display method of the remote station information

Setting the search channels for the BAND SCOPE function

Selecting a Display Language

Adjusting the LCD Backlight and Keypad Key Light Brightness Level

Voltage Measurement Function/Temperature Measurement Function

Changing the Display Pattern of the PO Meter

Setting the transmission modulation level

Switching between digital and analog mode

Setting the squelch type for the digital mode

Displaying the version of the DSP program

Muting Voice

Setting memory bank link

Assigning a name to a memory bank

memory channel number Memory Channel Write Function

Calling Only a Specific Station New Pager Function

Setting the signal strength to output sound S Meter Squelch Function

Setting the squelch type for transmission and reception SQL EXPANTION FUNCTION

ON/OFF for the Weather Alert Feature

Turning illumination off when scanning stops SCAN LAMP Function

Setting the range for SCAN

Turning off the power automatically APO Function

FT1DR

What is WIRES-X

Terminology

Connecting to a Faraway Station Using WIRES-X

Connecting in digital mode

Connecting to a node or room on the Internet

Communicating with others

Connecting to a registered node or room

Releasing the WIRES-X connection

Disconnecting from a node or room

Returning to the initial screen

Using the News Function of WIRES-X

Viewing text data in a node or room on the Internet

Importing images

Importing images from the WIRES-X server

Viewing imported data later

Deleting imported data

Listening to audio messages

Listening to the WIRES-X server (INT NEWS information

Listening to information on a node or room on the Internet

Transmitting messages and images

Transmitting data to a node or room on the Internet

Transmitting an audio message

Using WIRES-X and the GM Function Simultaneously

Using the News Function of WIRES-X in GM Operation

WIRES-X Setting Mode Menus

Setting the transmission frequencies for repeaters WIRES-X

Setting the item order on the node & room lists

Deleting the registered nodes and rooms

Error Message Guide

specifications

cntl unit

dsp unit

Installing/Removing the Battery Pack

Connecting an External Power Supply for Use in Vehicle

Connecting to an External Power Supply Using a Power Cable

Communication

To deactivate the radio function

Setting the Time Signal

Locking keys or switches

Writing into the Memory

Recalling the Home Channel

Restoring the Deleted Memory Channel

Registering a Memory Channel in a Memory Bank

Canceling Memory Channel Registration in a Memory Bank

Recalling a Special Bank to Listen to the International VHF (Marine) Radio

Programmable Memory Scan (PMS)

Using the Search Function

BACK TRACK Function

Using the BACK TRACK Function

Useful Functions

Memory channel Priority memory channel

Confirming the Entered DTMF Code by the Sound

Using the Tone Squelch Function

Selecting a DCS Code

Searching for the Frequency of the DCS Used by the Remote Station

Notification of Call from a Remote Station by the Bell Bell Function

Changing the Number of Times the Bell Rings

Turning on the New Pager Function

Set Mode Item List

FT1DR Specifications