ADT Safewatch Pro 3000 Installaton Manual

Also see for SafeWatch 3000: User guide BATTERY REPLACEMENT INSTRUCTIONS Programming guide

Contents

ADT Safewatch Pro 3000 Installaton Manual Manual pdf 30 page image

Safewatch Pro 3000 Installation Instructions4-2FIELD TITLE and DATA ENTRIES EXPLANATION*29 Long Range Radio Output0 = not used1 = using Long Range Radio outputUL Installations listed for UL must be 0(Long Range Radio disabled).If selected, all messages programmed to go to the primary telephoneline receiver will also be sent to the connected 7720PLUS, 7820,7835, or 7845 Radio (sent in Contact ID format). The data line issupervised as well as certain functions in the radio. Ifcommunication is lost or a trouble develops, an attempt will be madeto send a message via both radio and telephone to the central station.Program the radio for device address 3.Zone Sounds & Timing (∗31–∗39)FIELD TITLE and DATA ENTRIES EXPLANATION*31 Single Alarm Sounding Per Zone(per armed period)0 = no limit on alarm sounding per zone1 = limit alarm sounding to once per armingperiod for a given zoneUL installations must be 0 (no limit).*32 Fire Alarm Sounder Timeout0 = yes; fire sounder timeout after timeprogrammed in field ∗331 = no fire sounder timeout; continuesounding until manually turned offThis control complies with NFPA requirements for temporal pulsesounding of fire notification appliances.Temporal pulse sounding for a fire alarm consists of the following:3 pulses – pause – 3 pulses – pause – 3 pulses.*33 Alarm Sounder Timeout0 = No timeout 3 = 12 min1 = 4 min 4 = 16 min2 = 8 minThis field determines whether the external sounder will shut offafter time allotted, or continue until manually turned off.UL installations: must be set for a minimum of 4 min (option 1*34 Exit Delay00-99 = Exit Delay time for each partition insecondsThe system waits the time entered before arming entry/exit zones. Ifthe entry/exit door is left open after this time expires, an alarm willoccur. Common zones use same delay as partition 1.*35 Entry Delay #100-99 = Entry Delay time for each partitionin seconds.Upon entering, the system must be disarmed before the time enteredexpires, otherwise it sounds an alarm. Common zones use samedelay as partition 1.UL installations must be set for a maximum of 20 seconds.*36 Entry Delay 0200-99 = Entry Delay time for each partitionin seconds.Upon entering, the system must be disarmed before the time enteredexpires, otherwise it sounds an alarm. Common zones use samedelay as partition 1.UL installations must be set for a maximum of 20 seconds.*37 Audible Exit Warning0 = no exit warning sound1 = provide exit warning sound when armedAwayWarning sound consists of slow continuous beeps until last 5 seconds,then it changes to fast beeps. The warning sound ends when exittime expires.*38 Confirmation Of Arming Ding0 = no ding1 = confirmation ding after arming system2 = confirmation ding after arming from RFbutton or RF touchpad onlyConfirmation of arming is 1/2 second external sounder “ding.”If “1” selected, ding occurs when closing report is sent, or at the endof Exit Delay.If “2” selected, ding occurs upon reception of the wireless armingcommand.*39 Power-Up In Previous State0 = always power-up in a disarmed state1 = assume the system status prior topower downWhen the system powers up armed, an alarm will occur 1 minuteafter arming if a zone is faulted.Note that if the previous state was armed Away or Stay, the systemwill not respond to sensor changes for 1 minute, which allows timefor sensors such as PIRs to stabilize.UL installations: must be 1 (power-up in previous state)