Casio XW-P1 User Manual

Also see for XW-P1: Manual

Contents

Casio XW-P1 User Manual Manual pdf 66 page image

Using the Performance ModeE-64Editable Parameter ListEditable Performance Parameter ListDisplay Description SettingsZone Parame >EntZone parameters. This group includes parameters for each of the zones (Zone 1 through 4).• Use the 9 PART minus (–), plus (+) buttons to select the zone you want to edit.• You also can enter the group using the following shortcut: Perform step 2 under “To register aperformance” (page E-62) and then hold down 7 EDIT. This will enter the group.Zone Zone on/off. Turns all zones on or off This setting is different from the mixer function page (pageE-68) part on/off (Part Enable) setting. Off, OnToneTone. Selects the tone for each zone. This setting is the same as the mixer function part tone(page E-68).• While this item is selected, you can select a tone using the same operation as that used in theTone Mode.• This setting can also be configured using quick editing (page E-16).• There are some limitations on the selection of tone categories for Zones 2 through 4 (pageE-16).• A tone with DSP will have DSP next to the tone name on the display (page E-37).Zone 1:Solo Synth P00 toVarious U29Zone 2 to 4:Piano P00 toVarious U29KeyRangLowKey range low. Specifies the low key range of the keyboard for each zone. This setting is used incombination with the Key Range Hi setting to configure key ranges for each zone.For example, configuring F3 (low) to C7 (high) for Zones 1 and 2 and C2 (low) to E3 (high) forZones 3 and 4 will enable play of Zone 1 and 2 tones on the right side keyboard range in theillustration below, and the Zone 3 and 4 tones on the left side keyboard.• Setting can be specified using the keyboard keys.C-1 to G9KeyRangHi Key range high. Specifies the high range of the keyboard for each zone. This setting is used incombination with the Key Range Lo setting to configure key ranges for each zone. C-1 to G9Volume Volume. This setting is the same as the mixer function tone volume (page E-68). 0 to 127Pan Pan. Adjusts the left-right position of sound in the stereo field. This setting is the same as themixer function part panning (page E-68). –64 to 0 to +63Oct.Shift Octave shift. Shifts the tone of notes by octave units. –2 to 0 to +2Transpose Transpose. Shifts the tone of notes by semitone units. This setting is the same as the mixerfunction part coarse tune (page E-68). –12 to 0 to +12FineTune Fine tune. This setting is the same as the mixer function part fine tune (page E-68). –99 to 0 to +99BendRngDwn Bend range down. Pitch change amount for downward bender operation. 0 to 24BendRngUp Bend range up. Pitch change amount for upward bender operation. 0 to 24Rev Send Reverb send. This setting is the same as the mixer reverb send (page E-68). 0 to 127Cho Send Chorus send. This setting is the same as the mixer chorus send (page E-68). 0 to 127DSP Line DSP line. This setting is the same as the mixer function part DSP line (page E-68). Off, OnKnob1Enable Knob 1 on/off. Enables/disables 3 K1 operation for each zone. Off, OnKnob2Enable Knob 2 on/off. Enables/disables 3 K2 operation for each zone. Off, OnKnob3Enable Knob 3 on/off. Enables/disables 3 K3 operation for each zone. Off, OnKnob4Enable Knob 4 on/off. Enables/disables 3 K4 operation for each zone. Off, OnBend Enable Bender on/off. Enables/disables bs BENDER operation for each zone. Off, OnWheel Enable Modulation wheel on/off. Enables/disables bs MODULATION operation for each zone. Off, OnPedal Enable Pedal on/off. Enables/disables operation of a pedal plugged in to the ck SUSTAIN/ASSIGNABLE JACK for each Zone. Off, OnC2 F3E3 C7Zone 3Zone 4Zone 1Zone 2