Denon AVR-2312CI Owner's Manual

Also see for AVR-2312: Service manual Protocol guide Getting started

107SYSTEM SETUPAudio Setup Default settings are underlined.Make settings for audio playback.Setting items Setting details2ch Direct/StereoSelect the method forsetting the speakers usedin the 2-channel direct andstereo playback modes.Setting : Select the method for setting the speakers used in the 2-channeldirect and stereo playback modes.• Basic : The settings at “Speaker Setup” (vpage 102) are applied.• Custom : Make separate settings for 2-channel. Make the followingsettings:Front : Set the front speaker size.• Large : Use a large speaker that can adequately play back lowfrequencies.• Small : Use a small speaker that has inadequate playback capacity forlow frequencies.If “Speaker Config.” – “Subwoofer” (vpage 102) is set to “No”,the setting is automatically set to “Large”.Subwoofer : Set the presence of a subwoofer.• Yes : Use a subwoofer.• No : Select when a subwoofer is not connected.If “Speaker Config.” – “Subwoofer” (vpage 102) is set to “No”,the setting is automatically set to “No”. If the “Front” setting is“Small”, the setting is automatically “Yes”.SW Mode : Select low range signals to be reproduced by subwoofer.• LFE : When the “2ch Direct/Stereo” – “Front” setting is set to “Large”,the LFE signal alone is output from the subwoofer. Also, when the “2chDirect/Stereo” – “Front” setting is set to “Small”, the front channel lowrange signal is added to the LFE signal output from the subwoofer.• LFE+Main : The front channel low range signal is added to the LFE signaloutput from the subwoofer.This setting can be set made “2ch Direct/Stereo” – “Subwoofer” isset to “Yes”.Crossover : Set the maximum frequency of the bass signal output fromeach channel to the subwoofer.• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /250Hz• This setting can be set made “2ch Direct/Stereo” – “Subwoofer” is setto “Yes”.• If the “2ch Direct/Stereo” – “Front” setting is “Large” and the “SWMode” setting is “LFE”, “Full Band” is displayed and the setting cannotbe made.Setting items Setting details2ch Direct/Stereo(Continued)Distance FL / Distance FR : Select the speaker.• 0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set the distance tothe speaker.Set the difference in the distance between the speakers to less than20.0 ft (6.00 m).Level FL / Level FR : Select the speaker.• –12.0dB – +12.0dB (0.0dB) : Adjust the level of each channel.Auto Surround ModeMake setting formemorizing surround modesetting for each input signaltype.ON : Memorize settings. Automatically play with the last used surroundmode.OFF : Do not memorize settings. Surround mode does not changeaccording to input signal.• The auto surround mode function lets you store in the memory thesurround mode last used for playing the four types of input signals listedbelow.q Analog and PCM 2-channel signalsw Dolby Digital and DTS 2-channel signalse Dolby Digital and DTS multi-channel signalsr LPCM Multi-channel signals• When playing in PURE DIRECT, the surround mode does not changeeven if the input signal is changed.EQ CustomizeSet the disengagedequalizers to not displaywhen MultEQ® XT isselected.The equalizer mode in which“Not Used” is selectedcannot be stored andrecalled in the Quick Selectfunction.Audyssey Byp. L/R : Set when not using “Audyssey Byp. L/R” equalizer.• Used : Use.• Not Used : Do not use.Set so that “Audyssey Byp. L/R” settings can be made whenAudyssey® Auto Setup is performed.Audyssey Flat : Set when not using “Audyssey Flat” equalizer.• Used : Use.• Not Used : Do not use.Set so that “Audyssey Flat” settings can be made when Audyssey®Auto Setup is performed.Manual : Set when not using the “Manual” equalizer.• Used : Use.• Not Used : Do not use.