Denon DN-S3500 Operating Instructions Manual

Also see for DN-S3500: Service manual

Contents

4ENGLISHENGLISH#1 PITCH BEND – button#2 PITCH BEND + button• Pushing these buttons will change main playingspeed temporarily.• While pushing PITCH BEND + button, theplaying speed increases and speed decreaseswhile pushing PITCH BEND – button.• When these buttons are release, the playingspeed returns to the previous speed.#3 Pitch Slider• Use this slider to adjust playing speed faster orslower.#4 PITCH, RANGE button• Push this button to set the PITCH mode on andoff.• RANGE:Push this button for more than 1 sec to selectthe pitch range. The pitch range can be selectedwith the PARAMETERS knob from ±4, 10, 16,24, 50 or 100%.#5 KEY ADJUST button• Push this button to set the KEY ADJUST modeon and off.#6 PLATTER SOURCE buttonSelect the source for Scratch playback and themanual search/bend mode.• MAIN:This button lights up orange.Manipulate the Main Track sound.• SAMP.:This button lights up green only if a sample isloaded.Manipulate the Sampler sound via the scratchdisc.• BEND/SEARCH:When this button is pushed again, theBEND/SEARCH mode is selected.When the Scratch Disc selector is set toBEND/SEARCH during playback, it works as thepitch bend function by turning the scratch disc.When Scratch Disc is turned in the pause orstandby mode, it functions as the manualsearch function. In Manual search, you canmove the CUE point around by one frame at atime (1/75 second) with an audible frame-repeatsound, da-da-da-da.@5 CONT./SINGLE, RELAY button• CONT./SINGLE:A short tap of this button will toggle between 3possible END modes for playback.CONT. (continue: plays all tracks) SINGLE (stopsplaying and ReCUE’s back to your original setpoint), PLAYLOCK-see below.• SINGLE PLAY LOCK:SINGLE PLAY LOCK can be selected byPRESET. When SINGLE PLAY LOCK is selected,track selection during playback is disabled. Thisprevents playback from stopping when theTrack Select Knob is turned accidentally duringplayback. Play ending mode is the same assingle.• RELAY:You can turn on and off RELAY PLAY mode.Relay playback is possible when two DN-S3500s are connected by the MEMO in/outjacks.@6 FILE SEARCH MODE button• MP3 DISC only:When pushing this knob the file searchselection mode can be selected with thePARAMETERS knob.@7 TRACK/PARAMETERS knob• TRACK:When PARAMETERS LED is on, turn this knobto select tracks.By pushing this knob down while turning, thetracks will change by 10 tracks at a time.• PARAMETERS:When the PARAMETER LED is flashing, turnthis knob to select and change the parameterfor items found in the Platter effects, Memo,and Preset data, etc.@8 NEXT TRACK button• If this button is pushed during playback, the NEXTTRACK mode will be selected. The next track canbe selected with the PARAMETERS knob.@9 FAST SEARCH (6)QUICK JUMP button#0 FAST SEARCH (7)QUICK JUMP button• QUICK JUMP:When one of these buttons is tapped shortly,the playback position jumps approximately 10seconds in the forward (7) or reverse (6)direction. The jump time can be changed in thepreset mode.• FAST SEARCH:When one of these buttons is pressed and heldin, the disc is fast-searched in the forward (7)or reverse (6) direction.#7 SCRATCH direction select leverSelect the Scratch play direction.• BOTH:When the Scratch Disc is turned, the Scratchsound is heard in both stroke directions.• FWD:When the Scratch Disc is turned, the Scratchsound is heard in the forward direction only.#8 BRAKE button• Push this button to set the BRAKE.#9 DUMP button• Push this button to set the DUMP.$0 REVERSE button• Push this button to set the REVERSE.$1 TAP, LOCK, AUTO, INPUT BPMbutton• TAP:When you push this button repeatedly, the Automode turns off and starts measuring your BeatsPer Minute (BPM) by tapping.• LOCK:When this button is pressed once while theauto BPM counter is operating, the datameasured by the auto BPM counter is locked.• AUTO:When pushing the TAP button for 1 second,activates AUTO BPM mode.The measured BPM is displayed in the charactersection of the display.• INPUT BPM:When the TAP button is pressed and held in formore than 2 seconds, the BPM input mode isset and the BPM value can be input directly withthe EFFECTS knob. When the tap button ispressed again, the BPM input mode is turnedoff and set.NOTE:If you select a new track, AUTO BPM modeturns on automatically.$2 ECHO/LOOP button• The ECHO and ECHO LOOP functions can beselected. The feedback time and feedback ratiocan be selected. Looping for the feedback time(ECHO LOOP) is possible by setting thefeedback number to “MAX”.$3 FLANGER button• The feedback time and feedback gain can beselected.$4 FILTER button• One of three filters (LOW PASS, MID PASS andHIGH PASS) can be selected.$5 EFFECTS knob• Use this knob to set parameters of the internaleffector.$6 PLATTER LED• This vibrant blue bar provides platter modes at aglance such as, Scratch Memory, Pitch Bend,Frame Search and Loaded Disc.