Denon UD-M31 Operating Instructions Manual

Also see for UD-M31: Specification sheet Operating instructions Service manual

Contents

10ENGLISH• The supplied remote control unit (RC-933) is for use with the UD-M31 unit only.• If the cassette deck (DRR-M31) and MD recorder (DMD-M31) of the D-M31 series are connected to the main unit, youmay operate each of the above components using its respective remote control unit (refer to page 10,11).7 REMOTE CONTROL UNIT(1) Inserting the batteriesq Open the battery compartment cover of the remotecontrol unit.Press the knob and open the cover in the direction ofthe arrow.w Insert the two R03 (AAA) batteries, following the + and– marks in the battery compartment.e Close the cover of the battery compartment.Cautions on Batteries• Use R03 (AAA) batteries in this remote control unit.• Replace the batteries with new ones afterapproximately 1 year, though this depends on thefrequency with which the remote control unit isused.• Replace the batteries with new ones if the unit doesnot operate when the remote control unit isoperated from nearby, even if the batteries are lessthan a year old.• Be sure to insert the batteries in the properdirection, following the “ < ” and “ > ” marks inthe battery compartment.• To avoid damage or leakage of battery fluid:• Do not use a new battery with an old one.• Do not use two different types of batteries.• Do not short-circuit, take apart, heat or dispose ofbatteries in flames.• Remove the batteries when you do not plan to usethe remote control unit for an extended period oftime.• If the battery fluid should leak, carefully wipe off thefluid from the inside of the battery compartment,then insert new batteries.(2) Using the Remote Control Unit• The remote sensor is located on the CD receiver. Pointthe remote control unit at the remote sensor as shownon the diagram when operating it.• The remote control unit will operate from a directdistance of approximately 7 meters, but this distancewill be shortened if obstacles are present or if operatedat an angle. (The remote control unit will operate at anangle of up to 30° in either direction.)7m30°30°BBNOTES:• The remote control unit may not operate if theremote sensor is exposed to direct sunlight or thestrong light from a lighting fixture, or if there is anobstacle between the remote control unit and theremote sensor.• Do not press buttons on the remote control unit andon the set at the same time. Doing so could resultin malfunctions.• If the remote control unit is pointed away from there-mote sensor during continuous operations (suchas when turning the volume up or down), theoperation will stop. If this happens, point the remotecontrol unit at the remote sensor and press thebutton again.The UD-M31 comes with a system remote control unit (RC-933).BRC-933TONE /SDBREPEATCLEARDISCSKIPCALLPROG /DIRECTRANDOMEDITBAND1 2 354 67 8 9+1010POWERSYSTEMVOLUMERDSPTYGROUPCTPANELTUNING TUNINGENTERMEMORYTITLE /CHARACTER TIMEPRESETSLEEPTUNERFUNCTIONDISPLAY+-CDCD-R MDTAPE(3) Remote Control Unit Part Names and FunctionsTIME button• Press this button during the play orpause mode to switch the timedisplay.elapsed time per track↓remaining time for the track↓total remaining time on the disc(During programmed playback,indicate the total remaining time ofthe programmed tracks.)EDIT button• Press this button for editedrecording on a tape, dividing thetracks onto sides A and Baccording to the length of the tape.6 and 7(manual search) buttons8 and 9(automatic search) buttons2 (stop) buttonCD function buttonsEDIT button• Press this button to input thestation name.TUNING • and ª buttons• Use these buttons to selectingthe station.MEMORY button• Press this button to presetmemory.PRESET • / ª button• Use these buttons to recallpreset stations on the tuner.BAND button• Use this button to selecting theband.TUNER function buttonsFM AUTO FM MONOAM• Use this switch to turn on thepower of the entire system or setthe power to STANDBY mode.Power operation button• Press this button to set the sleeptimer.SLEEP button• Press this button to switch theinput (function).• The input changes in the followingorder each time this button ispressed.FUNCTION buttonCD TUNERTAPE(LINE2) MD(LINE1)• Press this button to adjust SDB(Super Dynamic Bass) and TONE.TONE/SDB button• Use these buttons to adjust thevolume.• The volume increases when the •button is pressed and decreaseswhen the ª button is pressed.VOLUME button• The display changes in thefollowing order each time thisbutton is pressed.DISPLAY buttonVolume level ClockFunctionNumber buttons• Press these buttons to specify thedesired track.CLEAR button• Press this button to clear the trackfrom the program.CD function buttonsRDS button• Use this button to automatically tune tostations using the radio data system.PTY button• Press this button after selecting“PTY” with the RDS button to selectone of the 15 program types.CT button• Use this to correct the time of theclock on the UD-M31. Press this buttonwhen the time service of an RDSstation is being properly received. “CT”and “TIME” are displayed for 2seconds and the UD-M31’s clock iscorrected. “NO CT” is displayed if theRDS station does not offer a timeservice and when the broadcast is notbeing received properly.PANEL button• Press this button when receivingRDS stations to select thefrequency, PS, PTY or RT display.• Note that this button will notfunction if the reception is poor.• The display mode changes as followseach time the button is pressed.• If a station name is not available,Station name mode will beomitted from the sequence.TUNER function (RDS) buttonsRDS PTY TPOFF• Press this button to set thefunction TUNER mode.TUNER button• Press this button to play or pauseof the CD player.CD 1/ 3 (play/pause) buttonRANDOM button• Press this button to set the tracksin random order.REPEAT button• Press this button for repeatplayback.PROG/DIRECT button• Press this button to switchbetween PROGRAM and DIRECTplay.CALL button• Use this button to confirm theprogrammed song.CD function buttonsNumber buttons• Press these buttons to recallpreset stationCLEAR button• Press this button to erase thestation name.TUNER function buttonsVolume level ClockFunctionPTYFrequencyStation name/PSRTStation name/PSFrequency