Denon UD-M31 Operating Instructions Manual

Also see for UD-M31: Specification sheet Operating instructions Service manual

Contents

21ENGLISH• If the RANDOM button is pressed while the repeatmode is set, the tracks are each played once inrandom order, then played again in another order,and so on.• The repeat mode is set to the all-track repeat modewhen the RANDOM button is pressed during single-track repeat mode.TONE /SDBREPEATDISCSKIPCALLPROG /DIRECTRANDOMEDITBAND1 2 3POWERSYSTEMVOLUMERDSPTYGROUPCTTUNING TUNINGENTERMEMORYTITLE /CHARACTER TIMEPRESETSLEEPTUNERFUNCTIONDISPLAY+-CDCD-R MD(8) Playing the tracks in random order ………………………………………………………………• Use this function to play all the tracks on the disc oncein random order.• In the normal playback mode, simply press theRANDOM button to set random playback.Random PlaybackRANDOM button(Using the remote control unit)Edited Recording on Sides A and B of a TapeThis function allows edited recording according to the length of the tape. (This operation is only possible from theremote control unit.)Edited recording is a system function of the D-M31 series. This function can only be used in combination with the DRR-M31.• Use this function to efficiently edit the tracks on a CD according to the length (time) of the tape onto which you wantto record.NOTES:• Load a blank cassette tape onto which you want to record in the cassette deck with side A on the top beforestarting the editing procedure. The tape is automatically wound to the beginning before recording starts.• The editing mode is canceled when the CD receiver’s stop button is pressed.• Note that even if the tape is slightly longer than the disc’s total playing time, it may not be possible to record allthe tracks on sides A and B because of the combination of tracks to be recorded on the different sides of the tape.• When recording on an already recorded tape, if the tape is longer than the new recording, the previous recordingwill remain at the end of side B, so erase the tape before starting.• During edited recording, only the stop button, power operation switch, and TIME button for the CD player sectionand the stop button and power operation switch for the cassette deck will function.• Set the reverse mode on the cassette deck (DRR-M31) to or during edited recording.• Edited recording does not function when you play a disc with more than 26 tracks.Example: Recording a disc containing 16 tracks and a total playing time of 56 minutes on a C-60 cassette tape(1) Recording the tracks in the same order as on the disc…………………………………………Automatic Edited RecordingON / STANDBYCD RECEIVER UD-M31TONE/SDBFUNCTIONMENU / SETBANDPHONESVOLUME+-2, 3 51TONE /SDBREPEATCLEARDISCSKIPCALLPROG /DIRECTRANDOMEDITBAND1 2 354 67 8 9+1010POWERSYSTEMVOLUMERDSPTYGROUPCTPANELTUNING TUNINGENTERMEMORYTITLE /CHARACTER TIMEPRESETSLEEPTUNERFUNCTIONDISPLAY+-CDCD-R MD54141 Press the FUNCTION button to set the CD mode.FUNCTION2Press the 5 (open/close) button to open the disctray.• Load the disc in the disc tray.3Press the 5 (open/close) button to close the disctray.• The display appears after several seconds.EDIT4Press the EDIT button on the remote control unit toset the length of the tape. (The length is the total forsides A and B.)• For a 60-minute (C-60) tape, press the EDIT button2 times.• The display changes as shown below each timethe EDIT button is pressed.(If the tape length has already been set once, thedisplay changes starting from that length.)Inputting other tape sizes:• To input other tape sizes, use the number and+10 buttons when “C ---” is displayed.After this, the remaining times for sides A and B aredisplayed alternately for several seconds5Press the 1/ 3 (play/pause) button.• The tape is automatically wound to the beginningon the cassette deck, then recording starts.Example: For a 60-minute tapeC-46 C-60 C-90 C---Side A display - Tracks 1 to 9 will berecorded on side A.2 minutes 40 seconds remaining onside ASide B display - Tracks 10 to 16 will berecorded on side B.1 minute, 20 seconds remaining onside B(Cancelling the editing mode)Track no. Elapsed time• To set a time other than 46, 60 or 90, input the time when “C —” is displayed. The time can be set to up to 99minutes input in the same way as when inputting track numbers for the CD direct search operation.• When the 1/ 3 (play /pause) button or 5 (open/close) button on the CD receiver is pressed while the power is set toSTANDBY mode, the power automatically turns on and the play or open/close operation is performed.• When the CD 1/ 3, TAPE 1, TAPE 0, or MD 1/ 3 button on the remote control unit is pressed while the power isset to STANDBY mode, the power automatically turns on and the play operation is performed.• In the same way, when the tuner TUNER buttons on the remote control unit is pressed, the power turns on and thecorresponding station is tuned in.13 AUTO ON FUNCTIONNOTES:• The total remaining time cannot be displayed during the random playback mode.• The random playback mode cannot be set during editing.