19ENGLISHON / STANDBYCD RECEIVER UD-M31TONE/SDBFUNCTIONMENU / SETBANDPHONESVOLUME+-Interrupting playback temporarily1/ 3 (play/pause) button 2 (stop) buttonPress the 1/ 3 (play/pause) button.The “ 3 ” mark appears on the display, andplayback stops at the point where the buttonwas pressed.Resuming playbackPress the 1/ 3 (play/pause) button.The “ 3 ” mark turns off on the display, andplayback resumes from the point where thepause button was pressed.Stopping playbackPress the 2 (stop) button.BANDNOTES:• When a disc is loaded, “ 00:00 ” is displayed on thedisplay for several seconds while the data on thenumber of tracks and total playing time is being readfrom the innermost side of the disc, after which thenumber of tracks and total playing time appear.• The CD SRS button of the cassette deck (DRR-M31)or MD recorder (DMD-M31) will not function ifpressed while the disc is being read. Please press thisbutton after the total playing time has been displayed.• If no disc is loaded, if the disc is upside down, or if thedata cannot be read properly due to scratches or dirt,the display reads as shown below and the disc willnot play.(Using the remote control unit)Example: Playing the 8th track1 Press the FUNCTION button repeatedly to select the CD operation.2Press the button corresponding to the number of the track 8.• “8” appears on the track number display and playback of tracknumber 8 begins.• When the end of the track is reached, playback continues on the next track.• To specify a track number of 11 or greater, say track 15, press then, and to specify a track number of 20 or greater, say track 23, press, , then .To play track 20, press then .• The system is in program play mode if “PROG” flashes in the display. Tocancel the “PROG” indication on the display, press PROG/DIRECT beforeyou input the desired track number.10+103+10+105+ 10Various Playback FunctionsTONE /SDBREPEATCLEARDISCSKIPCALLPROG /DIRECTRANDOMEDITBAND1 2 354 67 8 9+1010POWERSYSTEMVOLUMERDSPTYGROUPCTPANELTUNING TUNINGENTERMEMORYTITLE /CHARACTER TIMEPRESETSLEEPTUNERFUNCTIONDISPLAY+-CDCD-R MD12In addition to the regular playback, the UD-M31 also offers the following playback functions:(1) Playing a specific track ………………………………………………………………………………Direct Search(Using the remote control unit)1 When the REPEAT button is pressed once, “RPT” “ 1 ” appears on thedisplay and the single track repeat mode is set.2 Use the 8 and 9 buttons to select the track to be repeated.• When the end of the specified track is reached, playback starts over fromthe beginning of that track.• The single-track repeat mode can also be set by pressing the REPEATbutton once during playback.• To cancel the single-track repeat mode, press the REPEAT buttonrepeatedly until the “RPT” indicator turns off.TONE /SDBREPEATDISCSKIPCALLPROG /DIRECTRANDOMEDITBAND1 2 354 6POWERSYSTEMVOLUMERDSPTYGROUPCTTUNING TUNINGENTERMEMORYTITLE /CHARACTER TIMEPRESETSLEEPTUNERFUNCTIONDISPLAY+-CDCD-R MD231(2) Playing a single track repeatedly …………………………………………………………………Single- track Repeat3 Press the 1/ 3 (play/pause) button to start playback.(Using the remote control unit)1 When the REPEAT button is pressed twice, “RPT” “ALL” appears onthe display and the all-track repeat mode is set.2 Press the 1/ 3 (play/pause) button to start playback.• The all-track repeat mode can also be set by pressing the REPEAT buttontwice during playback.• To cancel the all-track repeat mode, press the REPEAT button to turn the“RPT” indicator off.• If the REPEAT button is pressed during programmed playback, the tracksare played repeatedly in the programmed order.TONE /SDBREPEATDISCSKIPCALLPROG /DIRECTRANDOMEDITBAND1 2 354 67 8 9VOLUMERDSPTYGROUPCTPANELTUNING TUNINGENTERMEMORYPRESETSLEEPTUNERFUNCTIONDISPLAY+-CDCD-R MD21(3) Playing all the tracks repeatedly ……………………………………………………………………All-track Repeat