www.eaton.com IM02601004E Page 249E Option CardsE.2. Optional I/O CardThe Power Xpert Meter can be equipped with an optional Discrete Input/Output (IO) card.The PXMIO-B card can be ordered with a new meter or as an field upgrade. This cardincludes 8 discrete inputs, 2 solid sate outputs, 3 relay outputs and a test LED.For field upgrade, de-energize equipment to prevent shock hazard.The meter includes sensitive electronic components. Caution should be used to avoidelectrostatic discharge to prevent equipment damage.1. Disconnect control power and verify that the health LED is no longer flashing beforeproceeding.2. Remove power supply card after the health LED stops flashing3. Remove the main communications board and optional CE card or blank filler plate.4. Carefully insert I/O card using card slot provided. Care should be taken that the cardalignment is correct before seating the card into the connector socket.5. Secure with screws at top and bottom.6. Reassemble the CE card or blank filler plate and main communications and power sup-ply, securing retaining screws on all cards.This card provides for external discrete I/Ointerfacing.S1 LEDMeter Test LED (Follows state of S1)S1 Solid State Form A OutputS2 Solid State Form A OutputMax Load: 100mAMax Voltage: 30VR1 Form C Relay OutputR1A Normally Open/R1B Normally ClosedR2 Form C Relay OutputR2A Normally Open/R2B Normally ClosedR3 Form C Relay OutputR3A Normally Open/R3B Normally Closed240 VAC30VdcMax 5 AmpDI1 - DI8Discrete Inputs Self sourced: 24Vdc ~10mA/input24Vdc Internal SourceDISDiscrete Input Source6PXMIO-B5A 240VAC30VDC987SELF SOURCE24VDC5432IO3-1100mA30VDC4IO2-3216 98753 41IO1-2R2BR3BR3CR3AR2AR2CR1BR1CS21R1AS22S12S11DI6DISDI8DI7DI5DI4DI3DI1DI2CWS1 LED10VA Source MAXPXCM-5TXDRXDC24+SHSHDBDACM6-321CM5-321Com 0 Display10VA Source MAXC24+SHCM4-321Com 1 RS485TXDRXDSHDBDACM3-321RXD/TXD10/100 T (RJ45)Local ConfigurationLink CM1CWCE4PXCE-B100 Fx (ST)LAN/WAN10/100 T (RJ45)TXD/RXDCom 2 RS485LinkCom 3 RS2321CE3-2 3DARXDTXDDTETXD RXDSHDBCE2TxCE1-RxCWAddressBase1513135Health11CW97StatusShortWarning!unpluggingCT's beforeCWPS1-100-240VACPXPS-1110-250VDC50W Max47-63 Hz21(+) L(-) NRatingDO NOT HIPOT / DIELECTRIC TESTAVERTISSEMENT: CET EQUIPEMENT RENFERME PLUSIEURSREMOVE POWER BEFORE SERVICING3GCIRCUITS SOUS TENSION. VOIR LE SCHEMA.MORE THAN ONE LIVE CIRCUIT. SEE DIAGRAM.WARNINGCWfor technical support1-800-809-2772 or 1-414-449-7100www.EatonElectrical.comCustomer Satisfaction2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, ANDINCLUDING INTERFERENCE THAT MAY CAUSEUNDESIRED OPERATION.E185559MEASURING EQUIPMENT20NL
