CHAPTER 5: SETTINGS FLEXLOGICC70 CAPACITOR BANK PROTECTION AND CONTROL SYSTEM – INSTRUCTION MANUAL 5-1515ELEMENT:Disconnect switchSWITCH 1 OFF CMDSWITCH 1 ON CMDSWITCH 1 CLOSEDSWITCH 1 OPENSWITCH 1 DISCREPSWITCH 1 TROUBLESWITCH 1 ΦA CLSDSWITCH 1 ΦA OPENSWITCH 1 ΦA BAD STSWITCH 1 ΦA INTERMSWITCH 1 ΦB CLSDSWITCH 1 ΦB OPENSWITCH 1 ΦB BAD STSWITCH 1 ΦB INTERMSWITCH 1 ΦC CLSDSWITCH 1 ΦC OPENSWITCH 1 ΦC BAD STSWITCH 1 ΦC INTERMSWITCH 1 BAD STATUSDisconnect switch 1 open command initiatedDisconnect switch 1 close command initiatedDisconnect switch 1 is closedDisconnect switch 1 is openDisconnect switch 1 has discrepancyDisconnect switch 1 trouble alarmDisconnect switch 1 phase A is closedDisconnect switch 1 phase A is openDisconnect switch 1 phase A bad status is detected (discrepancy betweenthe 89/a and 89/b contacts)Disconnect switch 1 phase A intermediate status is detected (transition fromone position to another)Disconnect switch 1 phase B is closedDisconnect switch 1 phase B is openDisconnect switch 1 phase B bad status is detected (discrepancy betweenthe 89/a and 89/b contacts)Disconnect switch 1 phase B intermediate status is detected (transition fromone position to another)Disconnect switch 1 phase C is closedDisconnect switch 1 phase C is openDisconnect switch 1 phase C bad status is detected (discrepancy betweenthe 89/a and 89/b contacts)Disconnect switch 1 phase C intermediate status is detected (transition fromone position to another)Disconnect switch 1 bad status is detected on any poleSWITCH 2 to 12 Same set of operands as shown for SWITCH 1ELEMENT:Teleprotectionchannel testsTELEPRO CH1 FAILTELEPRO CH2 FAILTELEPRO CH1 ID FAILTELEPRO CH2 ID FAILTELEPRO CH1 CRC FAILTELEPRO CH2 CRC FAILTELEPRO CH1 PKT LOSTTELEPRO CH2 PKT LOSTChannel 1 failedChannel 2 failedThe ID check for a peer relay on channel 1 has failedThe ID check for a peer relay on channel 2 has failedCRC detected packet corruption on channel 1CRC detected packet corruption on channel 2CRC detected lost packet on channel 1CRC detected lost packet on channel 2ELEMENT:Teleprotectioninputs/outputsTELEPRO INPUT 1-1 On↓TELEPRO INPUT 1-16 OnTELEPRO INPUT 2-1 On↓TELEPRO INPUT 2-16 OnFlag is set, Logic =1↓Flag is set, Logic =1Flag is set, Logic =1↓Flag is set, Logic =1ELEMENT:Thermal overloadprotectionTHERMAL PROT 1 PKPTHERMAL PROT 1 OPThermal overload protection 1 picked upThermal overload protection 1 operatedTHERMAL PROT 2 Same set of operands as shown for THERMAL PROT 1ELEMENT:Time of day timerTIME OF DAY 1 OFFTIME OF DAY 1 ONTIME OF DAY 1 STARTTIME OF DAY 1 STOPTime of day timer 1 is offTime of day timer 1 is onOne-second pulse at set time of day timer 1 start timeOne-second pulse at set time of day timer 1 stop timeTIME OF DAY 2 to 5 Same set of operands as shown for TIME OF DAY 1ELEMENT:Trip busTRIP BUS 1 PKPTRIP BUS 1 OPAsserted when the trip bus 1 element picks upAsserted when the trip bus 1 element operatesTRIP BUS 2 to 6 Same set of operands as shown for TRIP BUS 1Operand type Operand syntax Operand description
