245MEMORY OPERATION45 General descriptionThe transceiver has 207 memory channels including 6 scanedge memory channels (3 pairs), and 1 call channel. Each ofthese channels can be individually programmed with operat-ing frequency (pgs. 9, 10), duplex direction (p. 17) and offset(p. 21), subaudible tone encoder or tone squelch and its tonefrequency (pgs. 19, 48–50) and skip information* (p. 41).In addition, a total of 10 memory banks, A to J, are availablefor usage by group, etc.*except for scan edge memory channels. Memory channel selectionD Using the tuning dialq Push [M/CALL ]once or twice to selectmemory mode.• “M” indicator appears.w Rotate [DIAL] to selectthe desired memorychannel.• Programmed memorychannels only can be se-lected.D Using the [Y]/[Z] keysz Push [MR/CALL] to select memory mode.x Push [YY] or [ZZ] to select and set the desiredmemory channel.• Pushing [YY]/[ZZ] for 1 sec. activates a scan.• If scan is activated, push [YY]/[ZZ] again or push[CLR A(MW)] to stop it.D Using the keypadz Push [MR/CALL] to select memory mode.x Push [ ENT C(T-OFF)] to activate the keypadfor numeral input.c Push 3 appropriate digit keys to input a chan-nel number.• When inputting non-programmed channel num-bers, the previous memory channel appears.• Push only 1 appropriate digit key, [MONI 1(ANM)],[SCAN 2(T-SCAN)] or [PRIO 3(PTT-M)], then push[MM(TONE-1)] or [SQLZZ #(16KEY-L)] to select scanedge channels. “MM” and “#” can be used for “A”and “b” respectively.MR/CALLY/ZMR/CALLY/ZPRIOLOCKS E TANMMONIDUPLOWT-SCANTONEPRIOM/CALLSCANV/MHzDIGITAL PRIO AO BUSYMUTENARMIDLOW[DIAL]Appears

i supplied accessories

quick reference guide

battery connection

antenna installation

Turning ON transceiver

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

BASIC OPERATION

I Audio mute function

I S-meter squelch

I Selecting output power

REPEATER OPERATION

I Subaudible tones

I Offset frequency

I Reversed duplex mode

I Auto repeater

MEMORY OPERATION

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

I Programming channel names

I Memory clearing

I Memory bank selection

I Memory bank setting

I Transferring bank contents

CALL CHANNEL OPERATION

I Programming a call channel

SCAN OPERATION

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

priority watch

i priority watch operation

i programming a dtmf code

i transmitting a dtmf code

i pocket beep operation

tone scan

I Code programming

i pager operation

I Code squelch

I Digital mode operation

digital mode operation

i digital voice mode operation

I When receiving a Digital call

I Emergency communication

I Slow data communication

I GPS operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

i data cloning

specifications

troubleshooting

i fuse replacement

i optional unit installation

mode arrangement

Icom IC-2200H Instruction Manual

IC-2200H

HM-133V

LOGIC unit;

MAIN unit;

pll circuits

port allocations

parts list

HM-118TN

INSIDE VIEW

MECHANICAL PARTS LIST AND DISSASEMBLY

BOARD LAYOUT

SEMI-CONDUCTOR INFORMATION

receiver circuits

transmitter circuits

power supply circuits

main unit

receive adjustments