JBL DCR600 II Owner's Manual

Also see for CINEMA PROPACK 600: Owner's manual Service manual

48Configuring the DVD600II DVD ChangerNote that when a default subtitle language isselected, it will be used whenever that lan-guage is present on the DVD disc being played.However, when that language is not present,the language used will be the one prepro-grammed into the disc itself. (Again, typicallythat default will be English for discs sold inRegion 1, but the selection will vary at thediscretion of each disc’s producer.)Although the default will set the language thatwill be used when the disc is first put into play,the language may easily be changed at any timeby using the Subtitle Button .If you have no other changes to make after set-ting this default, press the Menu Button zto remove the Setup Menu from the screen, orpress the Play/Pause Button tobegin or resume playback.Selecting Menu LanguagesThe Menu Language option sets the defaultchoice for the language that will be used for theon-screen menu displays. This default settingDOES NOT impact the playback of DVD discs.To select the Menu Language default, you mustbe viewing the Setup Menu (Figure 1), which isavailable by pressing the Menu Button zwhile the unit is in the Stop mode. At the SetupMenu, press the ¤ Button until theMenus option is highlighted.To change the default Menu Language, pressthe › Button and note that the list ofsystem defaults will be replaced with a list ofthe available options, as shown in Figure 4. Thecurrent language choice will be indicated by afilled-in circle in the list on the right side ofthe screen.Figure 4To change the default setting, press the ⁄/¤Buttons y until the desired choice ishighlighted, and then press the Enter Button .Note that the circle for your choice will fill in,and the menu will return to the default listings.If you have no other changes to make after set-ting this default, press the Menu Button zto remove the Setup Menu from the screen, orpress the Play/Pause Button tobegin or resume playback.Parental Lock and PasswordsThe DVD600II enables you to control the discsthat are viewed by setting a ratings level. Whena disc that’s ready to play has a rating levelgreater than the default, it will not play. Tofurther protect against unauthorized viewing ofrestricted discs, the ratings-level option may belocked so that only authorized persons (such asa parent) may change the ratings level after apassword is entered.The ratings system is dependent on informationencoded into the DVD disc being played so,although most movies will carry an MPAA orother rating symbol, the disc may or may notcontain that rating in its software. In addition tothe five MPAA ratings of G, PG, PG-13, R andNC-17, the DVD600II will accommodate a totalof eight ratings steps, as set by the creators ofthe DVD format. These additional steps allowfor more critical control of program playback forall audiences.To select the permitted ratings values, you mustbe viewing the Setup Menu (Figure 1), which isavailable by pressing the Menu Button zwhile the unit is in the Stop mode. At the SetupMenu, press the ¤ Button until theRatings option is highlighted.To change the default Ratings setting, press the› Button and note that the list of systemdefaults will be replaced with a list of theprogram ratings, as shown in Figure 5. Someratings will be highlighted in light blue, whileothers will be highlighted in purple. Discs with arating in the light blue color band will play with-out any further action by the viewer. Discs withratings in the purple band will only play after apassword is entered.Figure 5To change the range of ratings that may beviewed without a password, press the⁄/¤ Buttons y until the desired rangeis set, and then press the Enter Button .Note that the circle for your choice will fill in,and the menu will return to the default listings.The listing in the default settings will show thehighest rated program that may be viewed with-out entering a password.If you have no other changes to make after set-ting this default, press the Menu Button zto remove the Setup Menu from the screen, orpress the Play/Pause Button tobegin or resume playback.Password Selection and Control LockThe Password System is used to control viewingof restricted programs and one’s capability tochange the password itself. The DVD600II isshipped without a password and with the set-tings for the password system unlocked. The fol-lowing instructions will show how to add apassword and to lock the settings.To set a password or lock the password system,you must be viewing the Setup Menu (Figure 1),which is available by pressing the Menu Buttonz while the unit is in the Stop mode. At theSetup Menu, press the ¤ Button until thePassword option is highlighted.To enter a password, press the › Buttonand note that the list of system defaults will bereplaced with a list of the three passwordoptions (Figure 6). If you change your mind anddecide not to enter, clear or change a password,press the ‹ Button ` to return to the mainmenu.To enter a password, check to make certain thatthe words “Set Password” are highlighted andthen press the Enter Button . The EnterPassword screen will then appear on your videodisplay (Figure 7).Figure 6