Kärcher SB-Wash 50/10 Manual

Also see for SB-Wash 50/10: Manual

- 13Interruption with a display of the operating panelFailure Possible cause Correction By whomIndicator lampflame monitoring,temperature limiterlights upFuel tank empty. Refill fuel tank. OperatorThe fuel filter is clogged Clean fuel filter. OperatorPhotocell flame monitoring is incorrectlyaligned or defectiveCheck the correct positioning of the photo-cell. OperatorMalfunction on the fuel pump or fuel sole-noid valveCheck parts and replace defective parts. Customer Ser-viceIndicator lampflame monitoring,temperature limiteris blinkingTemperature limiter has got triggered. Open the trigger gun until the system has cooled down.Switch the system on and off at the operator panel in or-der to unlock the temperature limiter. If the event re-curs, call Customer Service.OperatorMalfunctions with indication on the displayDisplay Cause Correction By whomE001 Set off the motor protection switch highpressure pumpReset the motor circuit breaker, in case of recurrence, callCustomer Service.OperatorE002 Fuse - F1 has triggered, circulatingpump, heat fanE003 Burner fault Switch off the system, wait briefly, switch on the system. OperatorE004 Tank permeate is empty (only with op-tion Top-Care)Refer to the operating instructions of the RO system (op-tion).OperatorE005 Detergent, fuel empty (option) Check the container, refill if necessary. Restart system. OperatorE100 Interruption control circuit Switch off the system, wait briefly, switch on the system. OperatorFaults without displayFault Possible cause Remedy By whomPlant is not running Mains fuse have got triggered Check mains fuses and mains voltage OperatorNo pressure build-up inthe plant or pump isknockingAmount of water supply is too low. Check water supply level (refer to technical data). OperatorHeating coil has heavy calciumdepositsbase exchanger (optional) or water softener with RM110 (optional) does not work. Rectify cause, decalcifythe plant.Operator, Cus-tomer ServicePipe is blocked Check all pipes to see that there are no blockages OperatorSystem is sucking air Check system for leaks, the detergent suction hosesmust lie in the detergent, refill detergent container.OperatorCheck the pump hose for cracks and wear; replace if re-quired.Operator, Cus-tomer ServiceProgram 4 (optional, byABS half load program5) no functionWrong adjustment in the functionmenueSet the "Osmosis" function in the function menu to"On".Operator, Cus-tomer ServiceNo reduced pressurewhen using program 2(only with ABS half load)Set the "Half-load" function in the function menu to"On".Operator, Cus-tomer ServicePump leaky (more than3 drops of water per min-ute)Defective pump part Replace defective part. Customer Ser-viceDetergent is not taken in Filter or hose is blocked Clean the parts. OperatorMagnet valve or check valve defect Replace valve. Customer Ser-vicePump hose of the dosing pump dam-aged.Check the pump hose for cracks and wear; replace if re-quired.Operator, Cus-tomer Servicehigh pressure pumpdoes draw airDetergent container is empty Refill detergent. OperatorBurner does not ignite orthe flame glows off dur-ing operationThe hot water was not adjusted for thiswashing program.No ignitionCheck the adjusting the control circuit board OperatorCheck ignition. Customer Ser-viceCheck ignition electrodes. Customer Ser-viceToo low water tempera-ture for hot water opera-tionsTemperature has been set too low. Set the thermostat to a higher level. OperatorHeating coil has heavy calcium depos-itsbase exchanger (optional) or water softener with RM110 (optional) does not work. Rectify cause, decalcifythe plant.Operator, Cus-tomer ServiceNozzle in spray pipe is rinsed out. Define the quantity to be transported by the pump. Re-place nozzle if the specifications given in the technicaldata are exceeded with a large margin.OperatorHeating coil sooted Remove the soot from the heating coil. Customer Ser-vice37EN