Kärcher SB-Wash 50/10 Manual
Also see for SB-Wash 50/10: Manual
                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |
- 16 Oil level has to be between MIN andMAX. Cut off tip of oil container cover Inser the overflow hoses of base ex-changer and salt tank in the drainagepipe of the building. Remove the lid of the base exchangerhead.1 Programme pointer2 Scala of the time switch Push and hold the red program indica-tor at the head of the circuit. With the other hand turn the camshafttowards the arrow (against the clock) atthe start of the field "back rinse", thecontrol light RM 110/Anti calc systemlights up. wait 1 to 2 minutes. Fill the salt tank with 10 liter of water Push the red program indicator at thecircuit head, and move it close to thefield "fill + clean wash" and turn it.. Aftera couple of minutes, the salt tank will befilled (duration approximately 9 min-utes). After it is filled, the water must beabove the strainerfloor of the salt tank. Pull the time switch, and turn to the ac-tual time. Put the lid of the base exchanger backon. Fill the salt tank all the way to the topwith salt in form of tabletts. Open the fuel tank and fill in fuel. Open the detergent container and fill indetergent.1 Dosing container Remove the cover of the dosing con-tainer and fill in RM 110. Close the lid again. Switch on the plant at the operator pan-el to "1/ON". Select cleaning programme 1. Check existing settings at the controlpanel or do your own settings. Check burner setting. Rectify the burn-er settings if the measured values devi-ate from the values given below.Note:Upon completion of the examination, closethe system door and check the burner func-tion with the system being completelyclosed. If the burner goes out due to a lackof air, the following measures can be taken: Remove the stopper from the floor ofthe plant. Partially remove the sealing on the doorsides. Also reduce the sealing startingfrom the bottom until 20 to 30 cm.We hereby declare that the machine de-scribed below complies with the relevantbasic safety and health requirements of theEU Directives, both in its basic design andconstruction as well as in the version putinto circulation by us. This declaration shallcease to be valid if the machine is modifiedwithout our prior approval.The signatories act on behalf of and withthe authority of the company management.Documentation supervisor:S. ReiserAlfred Kärcher SE & Co. KGAlfred-Kärcher-Straße 28-4071364 Winnenden (Germany)Tel.: +49 7195 14-0Fax: +49 7195 14-2212Winnenden, 2019/01/01Check oil levelInstallation of the base exchanger(optional)Filling in detergentsPour in water softener (optional)Initial Start-UpFuel pressure, approx. 1 MPa(10 bar)Blower pressure, approx. 0.22 kPa (2.2mbar)CO2 10...11%Emission temperature 180...200 °CEmission loss max. 10%Soot value max. 1EU Declaration of ConformityProduct: High pressure cleanerType: 1.319-xxxRelevant EU Directives2006/42/EC (+2009/127/EC)2014/30/EU2000/14/ECApplied harmonized standardsEN 60335–1EN 60335–2–79EN 55014–1: 2006+A1: 2009+A2: 2011EN 55014–2: 1997 + A2: 2008EN 61000–3–2: 2014EN 61000–3–3: 2006EN 62233: 2008Applied conformity evaluation method2000/14/EC: Appendix VSound power level dB(A)SB Wash 5/10Measured: 82Guaranteed: 84SB Wash E 5/10Measured: 69Guaranteed: 71Chairman of the Board of Management Director Regulatory Affairs & Certification40 EN |
Related manuals for Kärcher SB-Wash 50/10
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine