9ANTRIEBSTECHNIK1 1 905.01.99KEB COMBIVERT F4-CName:Basis1IntroductionGeneral© KEB Antriebstechnik, 1997All Rights reservedChapter Section PageDate6.3 Digital In- and Outputs ...................................................................... 6.3.36.3.1 Short Description Digital Inputs ........................................... 6.3.36.3.2 Input Signals PNP / NPN (di.1) ........................................... 6.3.36.3.3 Terminal Status (ru.14) ........................................................ 6.3.46.3.4 Set Digital Inputs with Software (di.15, di.16) ...................... 6.3.46.3.5 Digital Filter (di.0) ................................................................ 6.3.56.3.6 Inverting of the Inputs (di.2)................................................. 6.3.56.3.7 Edge Triggering (di.14) ........................................................ 6.3.56.3.8 Strobe-dependent Inputs(di.17...di.19) ................................ 6.3.66.3.9 Mode of Rotation setting (di.20 Bit0) ................................... 6.3.76.3.10 Functional Assignment (di.3...di.10) .................................... 6.3.86.3.11 Input status (ru.16) .............................................................. 6.3.86.3.12 Reset-Mode ST (di.21) ........................................................ 6.3.86.3.13 Short Description - Digital Outputs ...................................... 6.3.96.3.14 Output Signals ................................................................... 6.3.106.3.15 Output Conditions (do.1...do.4) ......................................... 6.3.106.3.16 Inverting Output Conditions do.17...do.24 ......................... 6.3.126.3.17 Selection Output Conditions (do.9...do.16) ........................ 6.3.126.3.18 Output Condition Interconnection (do.25) ......................... 6.3.126.3.19 Inverting of the Outputs (do.0) .......................................... 6.3.136.3.20 Output Terminal Status (ru.15) ......................................... 6.3.136.3.21 Used Parameters .............................................................. 6.3.136.4 Set Value and Ramp Adjustment ...................................................... 6.4.36.4.1 Short Description ................................................................ 6.4.36.4.2 AUX-Function ...................................................................... 6.4.46.4.3 Set Value Limits ................................................................... 6.4.96.4.4 Set Value Calculation ........................................................ 6.4.106.4.5 Fixed Frequencies (oP.22...24) .......................................... 6.4.116.4.6 Ramp Generator................................................................ 6.4.126.4.7 Used Parameters .............................................................. 6.4.186.5 Voltage-/Frequency Characteristic ................................................... 6.5.36.5.1 Maximal Frequency Mode (ud.11) ....................................... 6.5.36.5.2 Rated Point (uF.0) and Boost (uF.1) .................................... 6.5.36.5.3 Additional Rated Point (uF.2/uF.3) ....................................... 6.5.36.5.4 Delta Boost (uF.4/uF.5) ........................................................ 6.5.46.5.5 UZK-Compensation (uF.8) ................................................... 6.5.46.5.6 Modulation ........................................................................... 6.5.56.5.7 Operating Frequency (uF.11) ............................................... 6.5.66.6 Motor Presetting ................................................................................. 6.6.36.6.1 Motor Rating Plate .............................................................. 6.6.36.6.2 Motor Data from Rating Plate (dr.1...dr.4, dr.12) ................. 6.6.36.6.3 Motor Data from Data Sheets (dr.22) .................................. 6.6.36.6.4 Motor Stator Resistance (dr.5) ............................................ 6.6.4