100 Editing: Creating PlaylistsAfter setting the IN or OUT point, preview to check edit resulton the recorder.1 Press the PREVIEW button to preview.Start preview by pressing the PREVIEW button to playback the edited section on the recorder starting 3 secondsbefore the beginning of the edit section (PREROLL TIMEsetting) to 1 second beyond the end of the section.2 Events are indicated in orange during a preview.During a preview, a temporary event (an event displayedin orange) that indicates a temporary edit section iscreated on the timeline. This is referred to as a temporaryregistration. In this state, the event is not imported (notstored on the P2 card).3 Press the REC button to register an event.This operation records the required video section on theP2 card in the slot selected for recording. If required, usethe SLOT SELECT button to select the slot to be used forrecording prior to recording. This recording extends 2seconds beyond the IN and OUT points to allow room fortrimming after editing.4 The event is recorded and appears on the timeline.◆ NOTE:• To end preview, press the STOP button.• A temporarily registered section on an external device(RS-422A) used as the player is played back or reviewedwithout video or sound. A review plays back the entiretemporarily registered section.• To confirm the edit result without previewing it, press the RECbutton.• When an edit is started by defining only IN points of the playerand recorder, a temporary event of up to 24 hours will becreated on the recorder. Set an OUT point during the preview orpress the STOP button during capture to reset the length of theevent.• The margin before and after a temporarily registered sectionthat is imported in a capture is a maximum of 2 seconds. Datathat exceeds the IN and OUT points when a hard disk is used asthe player, and data that exceeds the start and end points ofmaterial when the player is an external device are not imported.• When the player is a device other than a P2 card, a previewwithout defining the IN and OUT points is not possible afterfinalizing the edit (after capture).• When an external device (RS-422A) is used as the player andthe time code of the external device is intermittent, the eventmay not be properly imported to the timeline even if the captureoperation works. As long as the OUT point shift is not longer than2 seconds, it is possible to revise the event after using thetrimming function for importing.• Audio levels cannot be set during registration or preview ofevents when the player is something other than a P2 card.• Audio channels cannot be switched during editing that uses anexternal device (RS-422A) as the player.➝ Refer to “Changing audio channel content” (page 93).• Events cannot be selected and menu operations are notavailable during temporary registration. To cancel temporaryregistration, press the CANCEL (SHIFT + EXIT) button.• When an external device (RS-422A) is used as the player, TCGappears on the recorder screen if the SHIFT and COUNTERbuttons are pressed simultaneously.• An external device cannot be selected as the player when setupmenu No. 27 (VDCP CMD) is ON.For a live recording, be sure to set the IN point of the recorder.1 Press the REC button to register an event.Preroll is performed from the IN point and playback start.At the IN point, the recorder pauses temporarily (about 1second), then recording starts.Recording stops when the OUT point is reached or theSTOP button is pressed.Preview and assigning events (when theplayer is an external device (RS-422A) orhard disk)PLAYLISTOFFMETERFULL/FINEMONITORSELECTMETER SELECTINPUT SELECTRECTHUMBNAILSETMENU IN ENTRYSLOT CLIPPF1 ALL CLIPPF3 SHIFTPF4CLIP LISTPF2SLOT SELECTLAST X TRIMDELETEVIDEO GO TOOUTEDIT MODE A.DUBMODEA1A3A2A4DIAGOPERATIONEXITCANCEL/PFMULTISELCH 1 CH 2 CH 3 CH 4 TEXTMEMO TCGTC PRESETPROPRESETCOUNTERPLAYER STOPSTILL/PAUSEPREVIEWA.LEVEL RECREWRECFFPREV NEXTPLAYREVIEW1 CLIP PLAYSOURCE SELECTNEWINTREGENPRESETEXTMARKERVARUNITYVIDEO AUDIOCH 1-4 CH 5-813Registering events (live recording)