Others-52-N (F, E): Card Photoshot Picture Quality(during Card Photoshotrecording)[F] means Fine, [N] meansNormal and [E] means Economy.-39-, , : MPEG4 Picture Quality -41-ACCESS: While Card is being read (duringPlayback, Formatting andMulti-Picture Function use). -38-0: Remaining Number of CardPhotoshot pictures -39-R:0h00m: Remaining time of MPEG4 orVoice dataH, L: Card Continuous PhotoshotRecording -39-: Lock Setting -47-¥ (White): DPOF Setting completed (set to1 or more picture) -46-¥ (Green): Slide Show Settings completed-44-¥ (Blue): DPOF Setting (set to 1 or morepicture)/Slide Show Settings bothcompleted -44-, -46-: [640k480] Image size≥For images not recorded with this MovieCamera, the size display is determined asfollows according to the number of horizontalpixels.: 640 or more, less than 800 (Thesize is not displayed at under640 pixels.): 800 or more, less than 1024: 1024 or more, less than 1280: 1280 or more, less than 1600: 1600 or more, less than 2048: 2048 or more(Cyan): Card Photoshot Mode(Red): While Card Photoshot recordingis activated(Red): No Card (Still Picture Mode)(Cyan): Moving Picture (MPEG4)Recording(Red): While Moving Picture (MPEG4)recording is activated(Red): No Card (MPEG4 Mode)(Cyan): Voice Recording Mode(Red): While Voice Recording isactivated(Red): No Card (Voice Recording Mode)ª To Change the Counter Display ModeBy changing [C.DISPLAY] on the[DISPLAY SETUP] Sub-Menu, you can changethe Counter Display Mode to Tape CounterIndication [COUNTER] (0:00.00), MemoryCounter Indication [MEMORY] (M0:00.00), andTime Code Indication [TIMECODE]N F SF640640SVGAXGASXGAUXGAQXGAPICTUREPICTUREPICTUREMPEG4MPEG4MPEG4VOICEVOICEVOICE(0h00m00s00f). (-15-) By repeatedly pressing the[COUNTER] Button on the Remote Controller,you can change the Counter Display Mode.ª To Display Date/Time IndicationTo display Date/Time Indication, set theappropriate Date/Time in [DATE/TIME] on the[DISPLAY SETUP] Sub-Menu. (-15-)You can also press the [DATE/TIME] Button ofthe Remote Controller repeatedly to display orchange the Date/Time Indication.ª To Change the Display ModeBy changing [DISPLAY] on the[DISPLAY SETUP] Sub-Menu, you can changethe Display Mode to All Function Display [ALL],Partial Display [PARTIAL] and Minimum Display[OFF]. (-15-)Owner IDYou can register your name and address in yourMovie Camera to identify the owner.1 Set [CAMERA FUNCTIONS] >>[OTHER FUNCTIONS1] >> [OWNER ID SET]>> [YES].≥The [OWNER ID] Menu appears.2 Turn the [PUSH] Dial (38) to select[PIN NUMBER] and press the [PUSH] Dial(38) to input desired numbers.3 Turn the [PUSH] Dial (38) to select numbersand press the [PUSH] Dial (38) to enterthem.≥Be sure to input 4 digits. Otherwise the PinNumber will not be registered.4 Press the [∫] Button.5 Repeat Steps 2–4 to input desiredcharacters for [NAME] and [POSTCODE].≥You can input up to 12 characters in [NAME],and up to 11 characters in [POSTCODE].6 Press the [∫] Button to finish the setup.To Verify Owner IDKeep pressing the [;] Button for approximately5 seconds.To Correct the ContentsIf Owner ID has already been set, carrying outStep 1 will display [INPUT PIN NUMBER] on thescreen. Input the Pin Number you have alreadyselected. If the number is not correct, the screenwill not change. If the number is correct, thecontents of the setup will be displayed. (Byrepeating Steps 2 to 4, you can change thecontents.)