Panasonic PT-VX42Z Operating Instructions Manual

Also see for PT-VX42Z: Operating instructions (functional manual)Manual 

Contents

Panasonic PT-VX42Z Operating Instructions Manual Manual pdf 109 page image

SpecificationsModel No. PT-VX42ZPower supply AC100 V - 240 V, 50 Hz/60 HzPower consumption100 V - 240 V, 3.5 A-1.3 A, 300 WWhen [STANDBY MODE] of [PROJECTOR SETUP] is set to [ECO]: 0.4 WWhen [STANDBY MODE] of [PROJECTOR SETUP] is set to [NORMAL]: 9 WLCD panelPanel size 1.6 cm(0.63") (aspect ratio 4 : 3)Display method 3 transparent LCD panels (RGB)Drive method Active matrix methodPixels 786 432 (1 024 x 768) x 3 panelsLens Manual zoom (1.2x) / Manual focusF 1.20 to 1.76, f 22.33 mm to 26.80 mmLuminous lamp 230 W UHM lampLight output *1 4 000 lmContrast ratio * 2 4 000 : 1 (all white / all black)([LAMP POWER] is set to [NORMAL], meanwhile [IRIS] is set to [ON])Applicablescanningfrequency* 3for Video signal (in-cluding S-video) Horizontal 15.75 kHz / 15.63 kHz, Vertical 60 Hz / 50 Hzfor RGB signal Horizontal 15 kHz to 100 kHz, Vertical 50 Hz to 100 HzDot clock frequency: 140 MHz or lessfor YPB PR signal[525i(480i)] Horizontal 15.75 kHz, Vertical 60 Hz[525p(480p)] Horizontal 31.50 kHz, Vertical 60 Hz[750(720)/60p] Horizontal 45.00 kHz, Vertical 60 Hz[1125(1080)/60i] Horizontal 33.75 kHz, Vertical 60 Hz[625i(576i)] Horizontal 15.63 kHz, Vertical 50 Hz[625p(576p)] Horizontal 31.25 kHz, Vertical 50 Hz[750(720)/50p] Horizontal 37.50 kHz, Vertical 50 Hz[1125(1080)50i] Horizontal 28.13 kHz, Vertical 50 HzHD/SYNC and V terminals are not compliant with 3 value composite SYNCfor HDMI signal525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/24p, 1125(1080)/24sF,1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p, 1125(1080)/60i, 1125(1080)/50iDisplayable resolution: VGA to WUXGA (non-interlace)Dot clock frequency: up to 162 MHzColor system 7 (NTSC, NTSC4.43, PAL, PAL-N, PAL-M, SECAM, PAL60)Projection size 1.07 m - 7.62 m (40"-300")Screen aspect ratio 4 : 3Projection scheme [FRONT/DESK], [FRONT/CEILING], [REAR/DESK], [REAR/CEILING] (Menu setting system)Speaker 1 (4.0 cm round-type)Maximum usable volume output 10 WThese values of light output are measured under the condition that [LAMP POWER] is set to [NORMAL], [PICTURE*1MODE] is set to [DYNAMIC] . Measurement, measuring conditions and method of notation all comply with ISO21118international standards.The value of contrast ratio is measured under the condition that [LAMP POWER] is set to [NORMAL], [PICTURE MODE]*2is set to [DYNAMIC], [IRIS] is set to [ON]. Measurement, measuring conditions and method of notation all comply withISO21118 international standards.For details of video signals that can be projected using this projector, refer to “List of compatible signals”. (*3 Æpages 107-108)ENGLISH - 109Chapter 6 Appendix - Specifications