Tascam DM-3200 Release Notes

Also see for DM-3200: Quick reference Owner's manual Manual Software guide Application guide

Contents

DM-3200 Release NotesTASCAM DM-3200 Release Notes 151 Pre-select the item type from the ITEM SELECTsection at the bottom left of the screen, using thePOD 1 knob.TIME EVENT: The GPI port will be controlled by thedesignated timecode value.KEY EVENT: The status of the transport key, F1-F12key, and the status of the MUTE key will control theGPI port.FADER EVENT: The GPI port will be controlled by thestatus of the fader.2 Using the cursor key, highlight a cell in the ITEMcolumn that you wish to set, and select the itemusing the JOG/DATA dial.Depending on which item type is selected in step 1 above,the options given vary as follows:TIME EVENT• : TIME EVENT or no assignment (------)KEY EVENT• : REW, FF, STOP, PLAY, REC, F1-F1, MUTE(CH1-48, BUSS1-16, AUX1-8), or no assignment (------)FADER EVENT• : FADER (CH1-48, BUSS1-16, AUX1-8, STEREO)or no assignment (------)3 Press the ENTER key to confirm the setting.Selecting the type•The Waveform to be output from each of the ports can beset in the TYPE column in the SETUP list.Use the cursor key to highlight a cell in the TYPE columnthat you want to edit, and select the item using the JOG/DATA dial.Depending on the type of the item you selected, the optionsgiven vary as follows:TIME EVENT: TYPE column will show “------” and the set-ting of the type is done in the GPI EVENT LIST on the rightof the screen.FADER EVENT: output low pulse when the fader starts: output high pulse when the fader starts: output low pulse when the fader stops: output high pulse when the fader stops: output low pulse when the fader starts or stops: output high pulse when the fader starts or stops: output changes to low level when the faderstarts, and to high level when the fader stops: output changes to high level when the faderstarts, and to low level when the fader stopsNOTE”When the fader starts” means when the fader level isbrought up from the lowest level.”When the fader stops” means when the fader level isbrought down to the lowest level.The Output pulse range is approximately 150ms.KEY EVENT•: output low pulse when the key status changes: output high pulse when the key status changes: change to low level when the key status isturned on, and to high level when the key statusis turned off: change to high level when the key status isturned on, and to low level when the key statusis turned offNOTEThe output pulse range is approximately 150ms.Options for F5-F8 are either low pulse output or highpulse output.ON/OFF setting•Set this to ON when you want to activate each of the GPI ports.When the TYPE is set to TIME EVENT, it will always displayOFF and the ON/OFF setting will be governed by thesetting in the GPI EVENT LIST on the right of the screen.TIME EVENT sectionYou can set up to 16 time events in the GPI EVENT LIST.How to control the GPI EVENT LIST•To move the cursor vertically within the list, use either• the up and down cursor key or the POD 4 knob.To move the cursor horizontally (across the columns),• use either the right and left cursor key.Arrows at the top and the bottom of the right-hand side• of the list mean that there are more time events outsideof the screen. To scroll the list vertically, use the POD4 knob. You cannot use the up and down cursor key toscroll the list.Selecting the port•GPI ports can be selected in the PORT column on the GPIEVENT LIST. You can only select a port whose item has beenset to be a TIME EVENT in the GPI CONFIG section. Use eitherthe cursor key or the POD 4 knob to highlight a cell in thePORT column that you want to edit, use the JOG/DATA dialto select the port, then press the ENTER key to confirm theselection. You can select the same port for more than onetime event.Setting the time•You can set the time when an event is to be executed. Useeither the cursor key or the POD 4 knob to highlight a cellin the TIME column that you wish to set, use the JOG/DATAdial to set the time, then press the ENTER key to confirm.Setting the type•You can set the output waveform type for each of theGPI ports.Use either the cursor key or the POD 4 knob to highlight acell in the TYPE column that you want to edit, then use theJOG/DATA dial to select the type.