Yaesu FT dx 1200 Operating Manual

Also see for FT DX 1200: Operation manual Operating manual Operating manual

Page 115FT D X 1200 O PERA T ING M ANUAL037 MOXFunction: Enables/disables the MOX operation.Available Values: ENABLE/DISABLEDefault Setting: ENABLE038 RF SQL VRFunction: Selects the operation mode of the RF/SQLknob.Available Values: RF/SQLDefault Setting: RF039 CAT RATEFunction: Sets the transceiver computer-interfacecircuitry for the CAT baud rate to be used.Available Values: 4800/9600/19200/38400 bpsDefault Setting: 4800 bps040 CAT TIME OUT TIMERFunction: Sets the Time-Out Timer countdown time fora CAT command input.Available Values: 10/100/1000/3000 msecDefault Setting: 10 msecThe Time-Out Timer shuts off the CAT data input after acontinuous transmission of the programmed time.041 CAT RTSFunction: Enables/Disables the RTS port of the CATjack.Available Values: ENABLE/DISABLEDefault Setting: ENABLE042 MEM GRPFunction: Enables/Disables Memory Group Operation.Available Values: ENABLE/DISABLEDefault Setting: DISABLE043 QUICK SPLIT FREQFunction: Selects the tuning offset for the Quick Splitfeature.Available Values: -20 ~ 0 ~ +20 kHz (1 kHz Step)Default Setting: +5 kHz044 TXW DIAL SELECTFunction: Selects the knob for tuning of the TXWfrequency during SPLIT operation.Available Values: VFO-A/VFO-BDefault Setting: VFO-BVFO-A: The TX frequency is tuned with the MainTuning Dial knob.VFO-B: The TX frequency is tuned with the [VFO-B/CLAR] knob.045 TX TIME OUT TIMERFunction: Sets the Time-Out Timer countdown time.Available Values: OFF/1 ~ 30 minDefault Setting: OFF (20 min, European version)The Time-Out Timer shuts off the transmitter aftercontinuous transmission of the programmed time.046 uTUNE DIAL STEPFunction: Selects the μ-TUNE mode.Available Values: DIAL STEP-1/DIAL STEP-2Default Setting: DIAL STEP-1DIAL STEP-1: Activates the μ-TUNE system using“COARSE” steps of the [VFO-B/CLAR]knob (2 steps/click) on the 7 MHz andlower amateur bands. On the 10/14 MHzbands, “FINE” [VFO-B/CLAR] knobsteps will be used (1 step/click).DIAL STEP-2: Activates the μ-TUNE system using“FINE” steps of the [VFO-B/CLAR]knob (1 step/click) on the 14 MHz andlower amateur bands.Advice: If an optional RF μTuning Kit is not connected,this adjustment has no effect.047 MIC SCANFunction: Enables/disables scanning access via themicrophone [UP]/[DWN] keys.Available Values: ENABLE/DISABLEDefault Setting: ENABLE048 MIC SCAN RESUMEFunction: Selects the Scan Resume mode.Available Values: PAUSE/TIMEDefault Setting: TIMEPAUSE: T h e s c a n n e r w i l l h o l d u n t i l t h e s i g n a ldisappears, then will resume after one second.TIME: The scanner will hold for five seconds, thenresume whether or not the other station is stilltransmitting.049 FREQ ADJFunction: Adjusts the reference oscillator.Available Values: -25 ~ 0 ~ +25Default Setting: 0To calibrate the frequency of your radio, you will needa frequency counter or set your receiver to one of thetime standard frequencies such as WWV or WWVH.The following example describes a calibration methodwhile receiving the WWVH time standard frequency inHawaii.1. Turn off both RX CLAR and TX CLAR function,before adjustment.2. Tune the radio to 15,000.00 MHz with CW-USBmode, then adjust the AF knob to comfortablelistening level.3. Enter Set Menu Item “ 049 FREQ ADJ”, and thenadjust the [VFO-B/CLAR] knob so that the BARdisplay is illumination in the center on the meter.menu moDe