IBM x3630 M3 7377 manuals
x3630 M3 7377
Table of contents
x3630 M3 7377
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- guidelines for trained service technicians
- safety statements
- Chapter 1. Start here
- Undocumented problems
- Chapter 2. Introduction
- Notices and statements in this document
- Features and specifications
- Server controls, LEDs, and connectors
- Rear view
- Internal connectors, LEDs, and jumpers
- System-board DIMM connectors
- System-board external connectors
- System-board jumpers
- System-board LEDs
- Fan board connectors
- Chapter 3. Diagnostics
- Event logs
- POST
- Checkout procedure
- Performing the checkout procedure
- Troubleshooting tables
- Hypervisor problems
- Intermittent problems
- USB keyboard, mouse, or pointing-device problems
- Memory problems
- Microprocessor problems
- Optional-device problems
- Power problems
- Serial device problems
- Software problems
- Universal Serial Bus (USB) port problems
- Power-supply LEDs
- IBM Dynamic System Analysis
- DSA editions
- DSA messages
- Tape alert flags
- Recovering the server firmware
- Automatic boot failure recovery (ABR)
- System event messages log
- Solving power problems
- Solving undetermined problems
- Problem determination tips
- Chapter 4. Parts listing, Type 7377 server
- Power cords
- Chapter 5. Removing and replacing server components
- System reliability guidelines
- Handling static-sensitive devices
- Internal cable routing and connectors
- Removing and replacing consumable parts and Tier 1 CRUs
- Removing a hot-swap power supply
- Installing a hot-swap power supply
- Removing the system battery
- Installing the system battery
- Removing and replacing Tier 2 CRUs
- Installing the cover
- Rotating the optional hot-swap rear hard disk drive cage up
- Rotating the optional hot-swap rear hard disk drive cage down
- Installing the air baffle
- Installing the PCI riser-card assembly
- Removing a riser card on the PCI riser-card assembly
- Installing a riser card from the PCI riser-card assembly
- Removing an adapter from the PCI riser-card assembly
- Installing an adapter on the PCI riser-card assembly
- Removing a ServeRAID controller from the PCI riser-card assembly
- Removing a memory module (DIMM)
- Installing a memory module
- dimm installation sequence
- memory mirroring
- Removing an IBM virtual media key
- Removing a USB hypervisor key
- Installing a USB hypervisor key
- Installing a ServeRAID controller battery on the remote battery tray
- Removing an optional ServeRAID adapter advanced feature key
- Installing an optional ServeRAID adapter advanced feature key
- Removing the USB board
- Installing the USB board
- Removing the operator information panel
- Installing the operator information panel
- Removing the front USB connector assembly
- Installing the front USB connector assembly
- Removing the hot-swap backplane on the optional rear hard disk drive cage
- Installing the hot-swap backplane on the optional rear hard disk drive cage
- Removing and replacing FRUs
- Installing a system fan
- Installing the system fan cage
- Removing the fan board
- Installing the fan board
- Installing the power-supply paddle card
- Removing the 3.5-inch HS HDD backplane
- Installing the 3.5-inch HS HDD backplane
- Removing the 2.5-inch HS HDD backplane
- Installing the 2.5-inch HS HDD backplane
- Removing an optional hot-swap SAS/SATA rear 3.5-inch hard disk drive cage
- Installing an optional hot-swap SAS/SATA rear 3.5-inch hard disk drive cage
- Removing an optional hot-swap SAS/SATA rear 2.5-inch hard disk drive cage
- Installing an optional hot-swap SAS/SATA rear 2.5-inch hard disk drive cage
- Removing the fan from the optional rear hard disk drive cage
- Installing the fan to the optional rear hard disk drive cage
- Removing a microprocessor and heat sink
- Installing a microprocessor and heat sink
- Thermal grease
- Installing the system board
- Chapter 6. Configuration information and instructions
- Configuring the server
- Using the Setup utility
- setup utility menu choices
- Using the Boot Selection Menu program
- serverguide features
- Using the integrated management module
- Using the remote presence capability and blue-screen capture
- enabling the remote presence feature
- Using the USB memory key for VMware hypervisor
- Configuring the Gigabit Ethernet controller
- Using the LSI Logic Configuration Utility program
- starting the lsi logic configuration utility program
- Configuring a ServeRAID controller
- Starting the Intel Matrix Storage Manager option ROM program
- IBM Advanced Settings Utility program
- Updating IBM Systems Director
- Updating the Universal Unique Identifier (UUID)
- Updating the DMI/SMBIOS data
- Appendix A. Getting help and technical assistance
- Software service and support
- Appendix B. Notices
- Important notes
- Particulate contamination
- Documentation format
- Industry Canada Class A emission compliance statement
- Japan VCCI Class A statement
- Japan Electronics and Information Technology Industries Association (JEITA statement
- Taiwan Class A compliance statement
- Index
manualsdatabase
Your AI-powered manual search engine