Chapter 1414-20If any operation error occurs after changing the setting value, change the setting value to the original one.14.6.3 <024:CIS scan position during ADF scanning> 0011-3598iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iThis value is used when automatic scan position adjustment (TESTMODE>"2"SCAN TEST>"3"SHEET POS ADJ) fails.14.6.4 <026:Distance from the standby position of CIS to the shading start point> 0011-2004iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iWhite shading can be adjusted finely.Normally, do not change the setting value. If any operation error occurs after changing the setting value, change the setting value to the original one.14.6.5 <031Vertical scan start position adjustment> 0011-2005iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iAdjust the position at which vertical scanning of a book starts. The larger the adjustment value, the narrower the left-side margin of the image becomes.14.6.6 <032Horizontal scan start position adjustment> 0011-2007iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iAdjust the position at which horizontal scanning of a book starts. The larger the adjustment value, the narrower the top margin in the image becomes.14.6.7 <033Vertical scan magnification correction> 0011-2008iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iCorrect the magnification of vertical scanning of a book. The larger the adjustment value, the more the image stretches in the vertical scanning direction.14.6.8 <035: - 036:Reader motor speed change> 0011-2010iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iThough no market adjustment work needs to be carried out, enter factory defaults at image processor PCB replacement.14.6.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)> 0011-2011iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iAdjust the position at which vertical scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the left-side margin of theimage becomes.047: Vertical scan magnification correction (scanningon ADF)16 0-32 one unit=0.1%048: Horizontal scan magnification correction(scanning on ADF)16 0-32 one unit=0.1%049: - 053: Not used054: Pickup motor speed correction (when the ADF isused)16 0-32 one unit=0.1%055: - 192: Not used193: ADF special paper, standardized size: LGLmisidentification-ready0 0 : LEGAL1 : FOOLSCAP2 : M_OFFICIO3 : A_FOOLSCAP4 : FOLIO5 : G_LEGAL6 : A_OFFICIO7 : B_OFFICIO194: ADF special paper, standardized size: LTRmisidentification-ready0 0 : LTR1 : G_LTR2 : A_LTR195: ADF special paper, standardized size: LTR_Rmisidentification-ready0 0 : LTR_R1 : FOOLSCAP2 : OFFICIO3 : E_OFFICIO4 : G_LTR_R5 : A_LTR_R196: shading target value (red) 272 0-511197: shading target value (green) 272 0-511198: shading target value (blue) 272 0-511199: - 212: Not used213: XYZ correction value (X) of standard white plate 8273 1-9999214: XYZ correction value (Y) of standard white plate 8737 1-9999215: XYZ correction value (Z) of standard white plate 9427 1-9999216: - 350: Not usedNo. Function Default Setting range Unit
