Chapter 1414-24Select whether to enable or disable flicker reduction mode. Select "Enable" and enter a count to modify fusing temperature control to cancel fluorescent flickingduring printing.Implementation of this mode would degrade the throughput.14.7.1.2.7 Detailed Discussions of Bit 50011-1892iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to enable or disable silent mode. Select "Enable" to modify the registration loop amount and thus reduce noises or squeaks the registration rollersproduce after picking paper from the individual paper inlets.14.7.1.2.8 Detailed Discussions of Bit 60011-1894iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to enable or disable noise reduction mode during terminal temperature rises. Select "Enable" to start slowdown at a temperature lower than normalwhen printing on smaller-sized paper than B4. Slowdown control thus enabled prevents the thermal degradation of the fusing film grease, assuring smooth slidingamong the fixing film, heater and film guide to cut squeaks.14.7.1.3 SSSW-SW1514.7.1.3.1 List of Functions0011-1895iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iT-14-2114.7.1.3.2 Detailed Discussions of Bit 00011-1896iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to inhibit automatic delivery tray replacement while running jobs with an inner two-way tray mounted in position. Select "Enable" to inhibit auto-matic tray replacement.14.7.1.3.3 Detailed Discussions of Bit 10011-1897iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to halt stapling job when a finisher installed has run out of staples. Select "Enable" to halt staple jobs when the finisher has run out of staples.14.7.1.3.4 Detailed Discussions of Bit 20011-1898iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to display a tray full message when the maximum allowable stapled document count is exceeded with a finisher installed. Select "Enable" not todisplay the message.14.7.2 Numerin Parameter Settings (Numeric Prama.)14.7.2.1 List of Functions 0011-1900iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iBit Function 1 00 Inhibit automatic delivery tray replacement while runningjobsEnable Disable1 Halt stapling job when out of staples Enable Disable2 Inhibit tray full indication while the stapled documentcount is exceededEnable Disable3 Not used - -4 Not used - -5 Not used - -6 Not used - -7 Not used - -No. Function Default Setting range01: - 30: Not used31: Top registration adjustment (manual feed tray) 50 0 to 100, one unit = 0.1 mm32: Top registration adjustment (cassette) 50 0 to 100, one unit = 0.1 mm33: Top registration adjustment (duplex unit) 50 0 to 200, one unit = 0.1 mm34: Left-end registration adjustment (manual feed tray) 100 0 to 200, one unit = 0.1 mm35: Left-end registration adjustment (cassette 1) 100 0 to 200, one unit = 0.1 mm36: Left-end registration adjustment (cassette 2) 100 0 to 200, one unit = 0.1 mm37: Left-end registration adjustment (cassette 3) 100 0 to 200, one unit = 0.1 mm38: Left-end registration adjustment (cassette 4) 100 0 to 200, one unit = 0.1 mm39: Left-end registration adjustment (duplex unit) 100 0 to 200, one unit = 0.1 mm
