If we learn MAC addresses for the LAG, status is shown for those as well.dot3aCurAggVlanIdSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.1.1.0.0.0.0.0.1.1 = INTEGER: 1dot3aCurAggMacAddrSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.2.1.0.0.0.0.0.1.1 = Hex-STRING: 00 0000 00 00 01dot3aCurAggIndexSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.3.1.0.0.0.0.0.1.1 = INTEGER: 1dot3aCurAggStatusSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.4.1.0.0.0.0.0.1.1 = INTEGER: 1 << Statusactive, 2 – statusinactiveLayer 3 LAG does not include this support. SNMP trap works for the Layer 2 / Layer 3 / default mode LAG.SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDownIF-MIB::ifIndex.33865785 = INTEGER: 33865785SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changedinterface state to down: Gi 0/0"2010-02-10 14:22:39 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDownIF-MIB::ifIndex.1107755009 = INTEGER: 1107755009SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changed interfacestate to down: Po 1"2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500932) 23:36:49.32 SNMPv2-MIB::snmpTrapOID.0 = OID:IF-MIB::linkUp IF-MIB::ifIndex.33865785 = INTEGER: 33865785 SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 =STRING: "OSTATE_UP: Changed interface state to up: Gi 0/0"2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500934) 23:36:49.34 SNMPv2-MIB::snmpTrapOID.0 = OID:IF-MIB::linkUp IF-MIB::ifIndex.1107755009 = INTEGER: 1107755009SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_UP: Changed interfacestate to up: Po 1"Troubleshooting SNMP OperationWhen you use SNMP to retrieve management data from an SNMP agent on a Dell Networking router,take into account the following behavior.• When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the snmpwalkcommand, the output for echo replies may be incorrectly displayed. To correctly display thisinformation under ICMP statistics, use the show ip traffic command.• When you query an icmpStatsInErrors object in the icmpStats table by using the snmpget orsnmpwalk command, the output for IPv4 addresses may be incorrectly displayed. To correctly displaythis information under IP and ICMP statistics, use the show ip traffic command.• When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the snmpwalkcommand, the echo response output may not be displayed. To correctly display ICMP statistics, suchas echo response, use the show ip traffic command.776 Simple Network Management Protocol (SNMP)
