Eaton Cooper Power Series Installation And Operation Instruction Manual

Also see for COOPER POWER SERIES: Installation and operation instructions Installation instructions Installation instructions Installation and operation instructions Operation instructions

Eaton Cooper Power Series Installation And Operation Instruction Manual Manual pdf 37 page image

Cable locking sleevesTo prevent detachment of the control cable from the controlcabinet by unauthorized personnel, a cable-locking sleeve(Catalog Number KME4D-1772-X [replace X with quantity:maximum 5]) is available to enclose the cable plug. Theplug is passed through the sleeve and the sleeve is thenfastened from inside the control cabinet. There is no accessto the cable receptacle without opening the locked cabinetdoor and detaching the sleeve.BCT Terminal blocks accessoriesSeparate BCT terminal blocks provide a connection pointfor external 600:5 or 1200:5 multi-ratio bushing currenttransformers. BCT terminal blocks are available for both theload or source sides and include wire for all ratios of theBCT. Refer to Table 8 and Figure 25.Auxiliary ter minal block accessoryAn auxiliary terminal block and receptacle is available for three-stage auxiliary switch wiring. Refer to Table 8 and Figure 25.Table 8. Terminal blocks (maximum 12-gauge wire)Description Catalog numberBCT shorting-type terminal block for (LOAD)bushings 2, 4, 6KME4D-1773-ABCT shorting-type terminal block for (SOURCE)bushings 1, 3, 5KME4D-1773-BTerminal block and receptacle for wiring of three-stage auxiliary switch, KA542R3KME4D-1801-11otee:N For every one terminal block accessory ordered, themaximum additional I/O allowed quantity is reducedby one.Auxiliary TerminalBlock AccessoryBCTTerminalBlocksFigure 25. Sample BCT terminal blocks configurationand positioning of auxiliary terminal block accessoryTable 9. Miscellaneous accessoriesDescription Catalog number120 VAC battery charger for spare batteries KME5-60-1Made in USA decal K89-407-1120 VAC GFI Duplex outletThe GFI Duplex Outlet (Catalog Number KME4D-1776)is available for controls powered by 120 VAC or 240 VACthree-wire supply power. This convenience outlet is rated for3 Amperes and is accessible through the front door in thecontrol cabinet. The 120 VAC GFI Duplex Outlet is used formany applications such as power for the MET Tester, auxiliarymeasurement equipment, and supplemental lighting.Automation accessory packagesThe Form 4D control includes an auxiliary power supplythat provides a customer connection to 13.5VDC. Thissource is intended to be used to power radios and othercommunications support equipment for connection toSCADA and other remote communications systems. Thepower supply is backed up by the control batteries in theForm 4D control cabinet, and will continue to provide powerto connected accessories under loss of AC line power to therecloser control. A maximum of 12W continuous and 30Wpeak (intermittent) power can be delivered to accessoriesconnected to the auxiliary power supply.A variety of automation packages are available to be usedin conjunction with the auxiliary power supply to facilitatethe mounting and proper connection of antennas to radiosmounted in the control cabinet. Packages are available tosupport many popular radio technologies and frequencybands. See Table 10 for details on each of the availableautomation accessory packages.Table 10. Automation accessory packages(A maximum of two accessories can be ordered.KME4D-1774-21 is not included in this maximum.)Description Catalog numberWireless communication provisions package13.5 VDC interface board, radio mounting tray(Radio and communications interface cards not included)KME4D-1774-21Cellular communications connection and protection package32” SMA(m)-N(m) coax pigtail, 700MHz - 2GHz PolyPhaser andmounting hardware, N(f)-type external terminationKME4D-1774-14*WiFi/WiMax communications connection and protectionpackage32” SMA(m)-N(m) coax pigtail, 2GHz-6GHz Polyphaser andmounting hardware, N(f)-type external termination, TNC(m)-SMA(m) inline coaxial adapterKME4D-1774-15*125MHz to 1GHz N-terminated radio connection and protectionpackage25” N(m)-N(m) coax pigtail, 125MHz to 1GHz PolyPhaserand mounting hardware, N(f)-type external terminationKME4D-1774-16*700MHz to 2GHz TNC-terminated radio connection andprotection package32” TNC(m)-N(m) coax pigtail, 700MHz to 2GHzPolyPhaser and mounting hardware,N(f)-type external terminationKME4D-1774-17*PolyPhaser and mounting hardware - 125MHz-1GHz KME4D-1774-A*PolyPhaser and mounting hardware - 700MHz-2GHz KME4D-1774-B*PolyPhaser and mounting hardware - 2GHz-6GHz KME4D-1774-C** Requires that the KME4D-1774-21 wireless communication provisionspackage also be ordered.32 operation inStrUCtionS MN280049EN September 2017Form 4D Microprocessor-based pole-mount recloser control installation and operation instructions