GE B30 Communications Manual
Also see for b30: Maintenance manualInstruction manualInstruction manualInstruction manualCommunications manual
                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    | |
Contents
|
3-218 UR FAMILY – COMMUNICATIONS GUIDEMODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS) CHAPTER 3: IEC 61850 COMMUNICATION3NeutSupn SPS Neutral overcurrent supervision status.The GND DIST Z1 SUPN IN operand.GndDisPDISNeutVx CMV Neutral point voltage in pu NuVUnPTOVNumCycPer INS Number of cycles of the nominal frequency. The CYCLES PER RECORD actualvalue.OscRDREOff SPS Logic 0 fixed operand Master/LLN0Offline SPS Indicate the motor is offline.The MOTOR OFFLINE operand.MotThmPTTROn SPS Logic 1 fixed operand Master/LLN0OnePoleOpn SPS One pole is open, others closed.The BREAKER 1 ONE P OPEN operand.Bkr0XCBROnePU ASG The per-unit base factor applied to the corresponding RxGOOSE analog inputFlexAnalog quantity to normalize it to a per-unit quantity.GGIO3OpAlm ACT Operate indicates the alarm decision of a protection function.The U/CURR ALARM OP operand.The UNDERPWR 1 ALARM OP operand.UnCurPTUC, UnPwrPDUPOpBia ACT B90 Operate indicates the trip decision of a biased protection logic B_DifPDIFOpHiSet ACT B90 Operate indicates the trip decision of the HISET element of breaker failurecurrent supervision function.B_BFaiPIOCOpLoSet ACT B90 Operate indicates the trip decision of the LOSET element of breaker failurecurrent supervision function.B_BFaiPIOCOpnCirc SPS Open circuit detected.The RRTD RTD 1 OPEN operand.The RTD Ip 1 OPEN operand.PRTDsSTMP, RRTDsSTMPOpnSt1 SPS Open status detected.The BREAKER/SWITCH OPEN operand.The RxGOOSE DPS1 Off operand.BkrΘXCBR, Bkr0XCBR,Disc0XSWI, DiscΘXSWI,GGIO3OpPhs1 SPS Indicates a trip decision for a particular cause per phase.The BUS 1 BIASED OP A/B/C operand.The BUS 1 UNBIASED OP A/B/C operand.The PHS DIST Z1 OP AB/BC/CA operand.BusDifPDIF, PhsDisPDISOpSig MV Operating signal, the analogue value used by the comparator.FLEXELEMENT 1 OpSig, in per unit.FlxElGAPCOpUnBia ACT B90 Operate indicates the trip decision of an unbiased protection logic B_DifPDIFOpV WYE Phase Operating Voltages.Bank Operating Voltage in per unit for Phase A, B, and C.CPhOvPTOVOscilGOOSE SPS One or more of GGIO1.Ind###.stVal has been frozen due to frequent statuschanges (chatter) in the mapped operand.The Oscillatory GOOSE operand.LPHDOtherInd SPS An LED.The LED OTHER operand.LEDsIHMIOvlTripTm MV Indicates estimation of trip time on overload.The ESTIMATED TRIP TIME ON OVERLOAD in seconds.MotThmPTTROutOfSrv SPS Out-of-service.The BREAKER 1 OOS operand.Bkr0XCBRP1Rip SPS Autoreclose A single pole is in progress.The AR 1-P RIP operand.Rec13pRRECP3Rip1 SPS Autoreclose 3-pole is in progress via dead time number indicated by the datainstance number.The AR 3-P/1 RIP operand.Rec13pRRECP3Tr SPS Force any trip to 3-phase trip.The AR FORCE 3-P TRIP operand.Rec13pRRECPFLLfail SPS Phase and/or frequency lock loop (PFLL) has failed.The 87L DIFF PFLL FAIL operand, which becomes On when the differentialelement's phase and frequency lock loop (PFLL) has failed.LinDfPDIFData objectnameCDC Semantics Used in logical nodes… |
Related manuals for GE b30
manualsdatabase
Your AI-powered manual search engine