H-4 D30 Line Distance Protection System GE MultilinH.1 CHANGE NOTES APPENDIX HHTable H–9: MAJOR UPDATES FOR D30 MANUAL REVISION Y2PAGE(Y1)PAGE(Y2)CHANGE DESCRIPTIONAll All Update Minor changes throughout documentAll All Delete Deleted CPU options U and V1-1 1-1 Update Updated Figure 1-1 Rear Nameplate3-8 3-8 Update Updated Figure 3-10 Rear Terminal ViewTable H–10: MAJOR UPDATES FOR D30 MANUAL REVISION Y1 (Sheet 1 of 2)PAGE(X2)PAGE(Y1)CHANGE DESCRIPTIONAll All Delete Deleted content pertaining to Ethernet switchTitle Title Update Changed part numbers. Updated address and contact information.1-1 1-1 Update Updated address and contact information2- 2- Add Added CPU options T,U, and V to order code table2- 2- Delete Removed E,G,H,J,S from CPU options from order code tables2-8 2-8 Delete Deleted 9S, 2S, 2T from replacement module order codes Tables 2-7 and 2-82-10 2-10 Update Changed number of phase distance and ground distance zones to 5 in Protection Elementssection 2.2.12-18 2-18 Update Updated Ethernet fiber table in section 2.2.8 Communications3-10 3-10 Update Updated Figure 3-12 Typical Wiring Diagram3-22 3-22 Update Deleted references to COM 1 RS485 port in section 3.2.9 CPU Communication Ports. Revisedtext and Figure 3-24 CPU Module Communications Wiring to include only modules T, U, V insection 3.2.9a.5-1 5-1 Update Updated the front panel main menu to include the CyberSentry security menu5-15 5-15 Update Update Communications main menu to remove the SNTP Protocol submenu5-16 5-16 Delete Deleted references to COM 1 RS485 port in section 5.2.4b Serial Ports5-16 5-16 Add Added section 5.2.4c Ethernet Network Topology5-16 5-16 Update Updated Networks section 5.2.4d to include all three Ethernet ports5-17 5-17 Update Added 0 as valid number to section 5.2.4e Modbus Protocol section5-38 5- Delete Deleted Local Time Offset, Daylight Savings Time, DST (start/stop for month/day/hour) from RealTime Clock menu5- 5-38 Add Added submenus Precision Time Protocol, SNTP Protocol, and Local Time and SynchronizingSource settings to Real Time Clock menu5- 5-39 Add Added new Precision Time Protocol (1588) menu and setting descriptions5- 5- Update Changed Communication to Real Time Clock in SNTP protocol settings path. Moved SNTPProtocol menu and settings descriptions to Real Time Clock subsection5-37 5- Delete Deleted section k) SNTP Protocol and the settings descriptions5- 5-42 Add Added new section for Local Time menu settings and settings description5- 5-50 Add Added new PTP Fail menu item to the User-Programmable Self Tests menu5- 5- Add Added PTP Failure and CLOCK UNSYNCHRONIZED to FlexLogic Operands table5- 5-111 Update Added row for DeltaTime to Table 5-: FlexElement Base Units5-218 5-218 Delete Deleted section 5.8.5c Remote Devices: ID of Device for Receiving GSSE/GOOSE Messages,meaning the Settings > Input/Outputs > Remote Devices settings5- 5-236 Add Added new CyberSentry security section and main menu, local passwords, session settings,restore defaults, and supervisory subsections to Chapter 56-1 6-1 Update Update Actual Values main menu to include Real Time Clock Synchronization submenu6- 6-7 Add Added new section for Real Time Clock synchronizing consisting of the menu of settings and thesetting descriptions6-10 6-10 Delete Deleted section 6.2.19 Ethernet Switch
