Gemini GEM-P801 Installation Instructions Manual

Also see for GEM-P801: Datasheet

Gemini GEM-P801 Installation Instructions Manual Manual pdf 12 page image

12WI1089 GEM-P801 Installation InstructionsUploading Signal Strength Informationfrom the LogAfter approximately (2) two hours, re-establish aconnection with the panel. Signal strength loginformation ranges from 1 to 10. The logging ofsignal strength should appear similar to thesample LOG below:Zone Features[00]Exit/Entry ZonesDelay allows exit and entry through an Exit/Entry Zone after the system is armed withoutsetting off an immediate alarm. Exit Delayallows the user to leave the premises afterarming. Entry Delay allows the user time toenter and disarm. The entry delay may becanceled by pressing F.[01]Home/Away with Delay ZonesZones that automatically bypass at theexpiration of the exit delay if the EXIT/ENTRY zone(s) are not violated. Zones ofthis type have a three (3) minute power-updelay, and do not display or cause analarm if faulted when the system powers up.Pressing the C key cancels the 3 minutetimer.If Exit/Entry zone(s) are violated during theexit delay, zones programmed as Home/Away with Delay Zone(s) will have a fixed20-second entry delay, if violated before theExit/Entry zone.To eliminate this fixed 20-second entrydelay, also program zones as Exit/EntryFollower Zones [02].To return protection to zones of this type,press BC from the keypad or [A1] or [A2]from a Keyfob. Program the Keyfob AUX 1or AUX 2 button for Full Set [81-7].[02]Exit/Entry Follower ZonesEntry Delay allows the user time to enterand disarm. Allows exit after the panel isarmed without setting off an immediatealarm and allows entry only if an Exit/EntryZone [00] has been violated first. Zones ofthis type have a three (3) minute power-updelay, and do not display or cause an alarm iffaulted when the system powers up.Pressing the C key cancels the 3 minutetimer.Group Bypassing - Zones programmed asExit/Entry Follower Zones will be Groupbypassed if the E key is pressed whiledisarmed or within the Exit Delay.Auto Interior Bypassing - Also programzones as Home/Away with Delay Zone(s)[01] to automatically bypass at the expirationof the exit delay if the EXIT/ENTRY Zone(s)are not violated during the exit delay.[03]Auto-Bypass Reentry ZonesZones programmed as this zone type arepermitted to be faulted at the time of arming.Once the zone is restored, while the controlpanel is still armed, the zone willautomatically be unbypassed and any subse-quent violations of the zone will cause analarm condition.[04]24-Hour ProtectionA zone that provides protection at all times,whether or not the system is armed.[05]40 ms Loop ResponseNormally loop response is 750 ms, select thisoption to change the loop response to 40 ms.The slower the loop response, the lesssensitive the system will be to intermittents(swingers). The programming option is not7/24/97 17:44 QL: Full Program Uploaded07/24/97 17:42 QL: Technical Connection(callback) Technician 207/24/97 15:23 Transmitter Status: GEM_SMK1(7A0DB5): SS=707/24/97 15:13 Transmitter Status: GEM_SMK2(768447): SS=807/24/97 15:13 Transmitter Status: Zone 2,SS=607/24/97 14:27 Trouble: RF Link,GEM_RECV 107/24/97 14:25 Panic: Keypad07/24/97 14:25 Panic: Keyfob 1(933780)SS=807/24/97 14:25 Dealer Program Mode Entered07/24/97 14:24 Instant: Keyfob 1(933780)SS=807/24/97 14:24 QL: Connection Terminated(10 MIN T/O)07/24/97 13:13 QL: Full Program DownloadedIf A0 is Entered during Exit Time, Home/Away withDelay Zones will be automatically bypassed, even if theExit/Entry Zone is violated. Easy Exit/Easy Arm [22-2] mustbe enabled.N OTE: