Gemini GEM-P801 Installation Instructions Manual

Also see for GEM-P801: Datasheet

Gemini GEM-P801 Installation Instructions Manual Manual pdf 23 page image

23System TroublesUse the System Trouble chart on the followingpage to determine the specific SystemTrouble(s).During normal panel operation the HSYSTEMTROUBLE LED has the following two modes ofoperation:STEADY 1-7 possible troublegroups, AC is presentFLASHING 1-7 possible troublegroups, AC is not presentViewing System Trouble(s)Press the A4 key on the keypad.To determine the System Trouble GroupNumber, count the number of times theHSYSTEM TROUBLE LED blinks. The keypadsounder will beep at the same rate that theHSYSTEM TROUBLE LED blinks.To determine the System Trouble, note the zoneLED that is ON. Look up the specific systemtrouble on the chart on the following page.The HSYSTEM TROUBLE LED and keypadsounder will continue to flash and beep. To viewthe next System Trouble, if any, press the Ekey. Continue pressing the E key, if there areno more system troubles to view, the system willreturn to normal operation.Note: System Troubles Groups 3 through 7 -System Trouble Groups that have a zone orsmoke detector associated with the trouble,such as RF low battery. The zone(s) of thedevice with a low battery will be displayed by theZONE LED . For example, a wireless lowbattery on zone 2 would beep the keypadsounder 3 times and turn on zone 2 LED.Audible System Trouble Indication - For allsystem troubles, except when the only systemtrouble is the loss of AC, the keypad will beeponce every 10 seconds. The keypad will continueto beep until the reset button is pressed or thetrouble has been acknowledged by pressing theC key.System Trouble ReportingThe following system troubles, when enabled toreport to Telco 1 [37-3] or Telco 3 [57-3], will sendthe report code programmed in Trouble Report[63] if reporting using a pulse format:System Trouble Pulse Report CodeBell Cut F12-Wire Fire Trouble F1Rcvr Fail-to-Respond F1Receiver Tamper F1Receiver JAM F1Tx Low Battery F1Tx Supervisory Failure F1Smoke Low Battery F1Smoke Sup. Failure F1If reporting using Point ID, a unique code will besent for each of the following System Troubles.System Trouble Point ID Report CodesBell Cut CODE 1 321 G00 ZN000-BELL 1 TROUBLE2-Wire Fire Trouble CODE 1 373 G00 ZN000-FIRE LOOP TRBLERcvr Fail-to-Respond CODE 1 382 G00 ZN000-SENSOR TROUBLEReceiver Tamper CODE 1 145 G00 ZN000-EXP. MODL. TAMPERReceiver JAM CODE 1 333 G00 ZN000-FIRE LOOP TRBLETx Low Battery CODE 1 384 G00 ZN00n-RF TRAN LOW BATTTx Supervisory Failure CODE 1 381 G00 ZN00n-SUPERVSN LOSS RFA 300 (SYSTEM TROUBLE RST) code is sent if a restore isreported after multiple troubles.System TroubleGroup #Keypad SYSTEM TroubleLED is flashing 1 timeindicating System TroubleGroup 1.Keypad Sounder beeps 1 timeindicating System TroubleEXAMPLE - LOW BATTERY SYSTEM TROUBLE DISPLAYZone LED(s) is ONindicates(Specific Trouble)Specific TroubleZone 2 LED is ON indicatingLow Battery. (1 Beep, LED 2)Flashing(System TroubleGroup Number)Enter A4 to enter System Trouble modeand determine the specific trouble. Press any key toview all system troubles.ARMEDHG E M I N I2STATUSBeeping(System TroubleGroup Number)FIGURE 9 S YSTEM TROUBLE E XAMPLE