Icom COMMUNICATIONS RECEIVER IC-R3 Instruction Manual Manual pdf 50 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Icom COMMUNICATIONS RECEIVER IC-R3 Instruction Manual

Also see for COMMUNICATIONS RECEIVER IC-R3: Service manualBrochure & specsService manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 preview
Contents
  1. supplied accessories
  2. Table Of Contents
  3. ACCESSORY ATTACHMENT
  4. Panel description
  5. Function display
  6. PANEL DESCRIPTION .................. 2
  7. VFO and memory channels
  8. Setting a frequency
  9. FREQUENCY AND CHANNEL SETTING ....................................... 7
  10. Receiving
  11. Setting volume level
  12. Monitor function
  13. Display backlighting
  14. General
  15. Programming after selection
  16. Memory bank selection
  17. Memory names
  18. Scan types
  19. Full/band/programmed scan
  20. Memory (bank) scan
  21. Selecting scan edges
  22. Skip channel setting
  23. Frequency skip function
  24. Priority watch types
  25. Priority watch operation
  26. Tone squelch operation
  27. Pocket beep operation
  28. Tone scan
  29. duplex operation
  30. offset frequency
  31. BAND SCOPE
  32. TV operation
  33. ATV operation
  34. DIRECTION FINDING
  35. Set mode
  36. Dial select step
  37. Beep tones
  38. Power saver
  39. Dial speed acceleration
  40. Display mode selection
  41. Display brightness
  42. Cloning function
  43. Battery cautions
  44. TROUBLESHOOTING
  45. quick reference
  46. QUICK REFERENCE ................. 57
Icom COMMUNICATIONS RECEIVER IC-R3 Instruction Manual Manual pdf 50 page image
 Battery cautionsNEVER incinerate used battery packs. Internal battery gasmay cause an explosion.NEVER immerse the battery pack in water. If the battery packbecomes wet, be sure to wipe it dry BEFORE attaching it tothe receiver.NEVER short terminals of the battery pack. Also, current mayflow into nearby metal objects so be careful when placing bat-tery packs in handbags, etc.If your battery pack seems to have no capacity even afterbeing charged, completely discharge it by leaving the powerON overnight. Then, fully charge the battery pack again. If thebattery pack still does not retain a charge (or very little), anew battery pack must be purchased.Use Icom battery packs, chargers or cables only. The use ofnon-Icom products may impair receiver performance and in-validate the warranty. Battery chargingPrior to using the receiver for the first time, the battery packmust be fully charged for optimum life and operation.CAUTION: To avoid damage to the receiver, turn it OFFwhile charging.• Recommended temperature range for charging:0°C to +35°C; +32°F to +95°F• Use the wall charger (BC-136A/D*) or optional desktopcharger (BC-135 for rapid charging) only. NEVER use an-other manufactures’ charger.* Not supplied with some versions.• An optional cable CP-18A/E (for 12 V cigarette lightersocket) can be used in-stead of the AC adapters of theabove chargers.CAUTION: BE SURE to remove the CP-18A/E when charg-ing is finished, because, a slight current still follows in theCP-18A/E and the vehicle’s battery will become exhausted.◊ Battery pack installationq Remove the battery cover from the receiver.w Remove the supplied battery spacer for alkaline batteryuse.e Install the Li-Ion battery pack (BP-206).• Be sure to observe the correct direction.• Charge Li-Ion battery pack before use.•Battery pack installation •Battery pack removal14 BATTERY CHARGING46
/ 64
Related manuals for Icom COMMUNICATIONS RECEIVER IC-R3
Icom COMMUNICATION RECEIVER IC PCR100 Instruction Manual first page preview
Icom COMMUNICATION RECEIVER IC PCR100 Instruction Manual
Icom IC-R1 Instruction Manual first page preview
Icom IC-R1 Instruction Manual
Icom IC-R2 Instruction Manual first page preview
Icom IC-R2 Instruction Manual
Icom IC-R5 Instruction Manual first page preview
Icom IC-R5 Instruction Manual
Icom IC-R6 Instruction Manual first page preview
Icom IC-R6 Instruction Manual
Icom IC-R2 Instruction Manual first page preview
Icom IC-R2 Instruction Manual
Icom IC-R5 Instruction Manual first page preview
Icom IC-R5 Instruction Manual
Icom IC-R6 Instruction Manual first page preview
Icom IC-R6 Instruction Manual
Icom IC-R10 Instruction Manual first page preview
Icom IC-R10 Instruction Manual
Icom IC-R75 Instruction Manual first page preview
Icom IC-R75 Instruction Manual
This manual is suitable for:
COMMUNICATIONS RECEIVER IC-R3
Manuals database logo
manualsdatabase
Your AI-powered manual search engine