Kenwood VRS-N8100 Instruction Manual

Also see for VRS-N8100 - AV / Digital Multimedia Receiver: DivX Playback guide Service manual Instruction manual

Contents

23 ENPreparations6Adjust the speaker volume level. Speaker LevelFrom your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.÷ In this step 6, only the speaker channels that have been setand require the volume level adjustment are displayed.1 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)to select “Speaker Level” on setup displays, and pressthe ENTER (or the Enter key).2 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)to select “Test Tone Auto”, “Test Tone Manual “ or“Test Tone Off”.Test ToneAutoTest ToneManual ExitTest ToneOffTRSEEPSCETEAIKTVEOERNRESLAEEUTVTUEOPL1 “Test Tone Auto”: Select this setting to adjust the speakervolume levels using the test tone. The test tone will be outputfrom every speaker channel in automatic sequence.2 “Test Tone Manual”: Select the speaker channel tooutput the test tone using the MULTI CONTROL@ / #(or the Multi @ / # key).3 “Test Tone Off”: Select to adjust the speaker volumelevels using the current output signals. The speakerchannel to output the signal can be selected using theMULTI CONTROL@ / # (or the Multi @ / # key).4 “Exit”: Select “Exit” and press the ENTER (or the Enter key)to return to the previous display.÷ Press the SETUP (or Setup) key to cancel the SETUPmode in the middle.When “Test Tone Auto” or “Test Tone Manual” is se-lected and the ENTER (or the Enter key) is pressed again,the test tone output will start.Use the MULTI CONTROL % / fi (or the Multi % / fi keys)to adjust the volume level of the test tone output fromthe speaker channel to be adjusted.For “Test Tone Auto” selection, the first test tone isheard from the front left speaker for 2 seconds. The nexttest tone is heard from the speakers in the followingsequence for 2 seconds each.When the “BS/SW Amp Back Surr.” has been selected:Left Center Right Right SurroundLeft SurroundSubwoofer Back SurroundWhen the “BS/SW Amp Subwoofer” or “BS/SW AmpOff” has been selected:Left Center Right Right SurroundLeft Surround Left Back Surround Right Back SurroundSubwooferRRSL SWBSLSCLeft0 dB00 dB00 dB00 dB00 dB00 dB00 dB00 dBL E0FdTBTSEPSETA KTEORN ELAEUVTEOL÷ If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page arealso changed. e÷ When a speaker setup is set to off the volume level forthe corresponding speakers is reset to 0 dB.When “Test Tone Manual” or “Test Tone Off” is se-lected, press the MULTI CONTROL @/# (or the Multi@/# key) to select the speaker channel and thenpress the MULTI CONTROL %/fi (or the Multi %/fikey) to adjust the speaker volume level.RRSL SWBSLSCLeft0 dB00 dB00 dB00 dB00 dB00 dB00 dB00 dBL E0FdTBTSEPSETA KTEORN ELMEAVNEULA L3 Press the ENTER (or the Enter key) again to return tothe main setup displays.÷ The test tone is turned off and return to the main setupdisplays.7Input the distance to the speakers. Speaker DistanceThis setting allows the signals output from different speakers toreach the listening position simultaneously.÷ In this step 7, only the speaker channels that have been setand require the volume level adjustment are displayed.Measure the distance from the listening position to eachof the speakers.Jot down the distance to each of the speakers.Distance to Front speaker (L) : ____ feet (meters)Distance to Center speaker (C) : ____ feet (meters)Distance to Front speaker (R) : ____ feet (meters)Distance to Surround speaker (RS) : ____ feet (meters)Distance to Surround back speaker (RB) : ____ feet (meters)Distance to Surround back speaker (LB) : ____ feet (meters)Distance to Surround speaker (LS) : ____ feet (meters)Distance to Subwoofer (SW) : ____ feet (meters)Preparing for playbackContinued to next page