NAD T 187 Owner's Manual
Also see for T 187: Owner's manualService manual
                                                       | |
Contents
| 
TRIGGER SETUPThe T 187 features three configurable +12V DC Trigger Output that can beused to activate a component or system it is fed into. A Trigger Input is alsoavailable to turn on the applicable link it is associated to. Use a combinationof [A/S/D/F] and [ENTER] keys to navigate through the Trigger Setupmenu parameters.TRIGGER OUTTriggers are low voltage signals used to turn on/off other compliantdevices. The T 187’s three +12V DC Trigger Outputs (Trigger 1 Out, Trigger 2Out and Trigger 3 Out) are dependent upon the mode they are associatedwith. There are six choices where +12V DC output can be assigned andthese are – Main, Zone 2, Zone 3, Zone 4, Zone 2+3+4 and Source Setup.Main : +12V DC is available at the assigned Trigger Out when the T 187is at powered state.Zone 2, Zone 3, Zone 4, Zone 2+3+4 : When the applicable Zone isat powered state, +12V DC is available at the assigned Trigger Out.Source Setup : If Trigger Output is linked to ‘Source Setup,’ +12V DCis available at Trigger Out whenever the particularly assigned Source isselected. Please see also separate discussion about ‘Trigger Out’ underthe Source Setup (Normal View) section.DELAYThe availability of +12V DC at Trigger Out can be regulated. If it is desiredthat +12V DC is available without delay the moment Trigger Out is linkedto its assigned setting, set Delay to 0s. Otherwise, one can select through adelay time of 1s to 15s.AUTO TRIGGER INAuto Trigger IN allows external system controllers to toggle the associatedsection of the T 187 from ‘Standby’ to ‘On’ and vice versa.Main : From standby mode, the T 187 is powered ON when +12V DC isapplied at Trigger IN.Zone 2, Zone 3, Zone 4 : Applicable Zone is turned ON whenever +12VDC is present at Trigger IN.All : Main, Zone 2, Zone 3 and Zone 4 as described above will all beactivated given a +12V DC input at Trigger IN.See also ‘Item 8. +12V TRIGGER OUT, +12V TRIGGER IN of REAR PANELdiscussion as well as the ‘Trigger Out’ discussion under ‘Source Setup(Normal View).’LISTENING MODE SETUPThe T 187 has various listening mode options and is mostly configurable.These are provided to reproduce a variety of sound effects depending uponthe content of the source to be played. Use a combination of [A/S/D/F]and [ENTER] keys to configure the following settings.LISTENING MODESThe audio format as detected by the selected Source can be automaticallyconfigured and processed through the following options:DOLBYDolby Digital is the multi-channel digital signal format developed in theDolby laboratories. Discs bearing the Dolby Digital (double-D symbol) logowere recorded with up to 5.1 channels of digital signals, reproducing amuch better sound quality, with dynamic and spatial sound sensations thatare much better than in the previous Dolby Surround.A Dolby Digital audio input can be configured relative to its format asfollowsStereo: If the detected audio is of Dolby stereo format, you can defaultit to one of the following settings – Pro Logic, PLIIx Movie, PLIIx Music orNone.Surround: If the detected audio is of Dolby Surround format, you candefault it to one of the following settings –Surround EX, PLIIx Movie,and PLIIx Music, Stereo Downmix or None.None: If ‘None’ is selected, the Dolby Digital signal will be defaultedto the ‘Stereo’ or ‘Surround’ settings set forth at the ‘PCM’ option. Seediscussion below about ‘PCM’.OPERATIONUSING THE T 187 – SETUP MENU24ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine