NAD T 187 Owner's Manual
Also see for T 187: Owner's manualService manual
                                                       | |
Contents
| 
1 STANDBY BUTTONt Press this button to switch ON the T 187 from standby mode. TheStandby LED indicator will turn from amber to blue and illuminatethe VFD. Pressing the STANDBY button again turns the unit back tostandby mode.t The T 187 can also be switched ON from standby mode by pressingany of the front panel buttons.NOTEThe rear panel POWER switch must be in the ON position for the Standbybutton to activate.2 STANDBY LEDt This indicator will light up amber when the T 187 is at standbymode.t When the T 187 is powered up from standby mode, this indicatorwill illuminate blue.t If a Zone (Zone 2, Zone 3 or Zone 4) is ON and STANDBY buttonis pressed to switch the T 187 to standby mode, the VFD will beextinguished but the STANDBY LED remains illuminated blue.This indicates a Zone (Zone 2, Zone 3 or Zone 4) is still active. Thecorresponding active Zone icon(s) will also remain displayed in the VFD.t In order to completely shut down the T 187 with Zone 2, Zone 3and/or Zone 4 still ON, press and hold STANDBY button until theSTANDBY LED turns amber.3 NAVIGATION and ENTER BUTTONSThe navigation ([d/f/a/s]) and [ENTER] buttons have variousapplications specific to given modes. The middle round button isdesignated as [ENTER] button; this is normally pressed to complete aselection, procedure, sequence or other applicable functions.AM/FM modeToggle [ENTER] button to switch between “Tune” and “Preset” mode.Select “Tune” mode.t Pressing momentarily the [a/s] button will manually scan the AMor FM band.t Press and hold [a/s] for more than 2 seconds to search up ordown; the T 187’s tuner will stop at the next sufficiently strong signalit encounters.t Note that this function “wraps” - that is, it will continue to searchfrom one end of the AM or FM band to the other until it stops at astrong signal.Toggle [ENTER] button to switch between “Tune” and “Preset” mode.Select “Preset” mode.t Use [d/f] to step up or down AM/FM Presets. Unused presets areskipped over. Note that Presets must have been previously stored.Refer also to the item about STORING PRESETS (AM/FM/XM/DAB) at theLISTENING TO AM/FM RADIO section of the OPERATION page.XM mode (120V version model only)t Use the front panel [d/f] and [ENTER] buttons in combinationwith the [MENU] button to select through applicable XM menuoptions.DAB mode (230V version model only)t Use front panel [a/s] and [ENTER] buttons in combination with[MENU] button to select through applicable DAB menu options.4 REMOTE SENSORt Point the HTR 8 remote control at the remote sensor and press thebuttons.t Do not expose the remote sensor of the T 187 to a strong lightsource such as direct sunlight or illumination. If you do so, you maynot be able to operate the T 187 with the remote control.Distance: About 23ft (7m) from the front of the remote sensor.Angle: About 30 o in each direction of the front of the remote sensor.IDENTIFICATION OF CONTROLSFRONT PANELNAD T187© NAD T 187AV Surround Sound Preamp Processor T 187a SOURCE sVOLUMEMEMORYsadfINFODELETEAM/FM/DB TUNER MODE LISTEN MODE TONE TONE DEFEAT FRONT INPUT/MP4 5 6 717A B C ED12 13 14 15 16111 2 31810986ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine