NAD T 187 Owner's Manual
Also see for T 187: Owner's manualService manual
                                                       | |
Contents
| 
LEARNING CODES FROM OTHER REMOTESBegin by positioning the HTR 8 “nose-to-nose” with the source remote sothe two devices’ infrared windows are about 2 inches apart.t Enter Learning Mode: On the HTR 8, simultaneously press-and-hold for3 seconds both a Device Selector key and the [RES] key until the LearnLED (located between HTR 8’s ON and OFF buttons) turns steady green.t Press the HTR 8’s function key you wish to teach a command; the LearnLED will turn amber.t Press-and-hold the function key on the source remote: The HTR 8’sLearn LED will flicker amber for a second or two, then turn solid green.The command is learned.t Press the HTR 8’s Device Selector key again to exit the learning mode.If the Learn LED does not flicker amber you may need to vary the distancebetween the remotes. If the Learn LED turns red rather than green, thatparticular command of that source remote command could not be learned.Example: Learning “DVD Pause”Position the HTR 8 and your DVD player’s remote as described above.t On the HTR 8, simultaneously press-and-hold [DVD] and [RES]; the LearnLED turns steady green.t Press the HTR 8’s Pause [ ] key; the Learn LED turns amber.t Press-and-hold the corresponding Pause key of your DVD player’sremote control; the HTR 8’s Learn LED flickers amber and then turnssolid green. The command is learned.t Press [DVD] again to exit the learning mode.CANCEL OPERATIONYou can cancel configuring a key, by pressing the active Device Selector keybefore the learn process is complete; the Learn LED will turn red.PUNCH THROUGHThe HTR 8’s “punch-through” function allows you to retain a function keyfrom one Device Select “page” to another, so that, for example, the AMP[SURR MODE] function might still control the T 187 when the DVD DeviceSelector page is active.NOTEThe HTR 8’s [VOL] keys are pre-programmed as “punched-through” forall Device Select pages: [VOL] will operate the T 187’s master-volumeSFHBSEMFTTPGUIFDVSSFOUMZTFMFDUFEEFWJDF5IF<4633><$&/5&3 >BOE<46#>$IBOOFM7PMVNFDPOUSPMTTJNJMBSMZBSFQSFQSPHSBNNFEBTpunched-through.To set a punch through, after entering the Learning Mode, and pressing thedesired key to be punched through, simply press the device key twice ofthe device to punch through to. The status LED will turn green; press theDevice Selector key again to exit Learning Mode.Example: Punch-through AMP [SURR MODE] key to the DVD “page”t On the HTR 8, simultaneously press-and-hold [DVD] and [RES]; the LearnLED turns steady green.t Press [SURR MODE]; the Learn LED turns amber.t Press [AMP] twice; the Learn LED turns green.t Press [DVD] again to exit the learning mode.COPY A COMMAND FROM ANOTHER KEYYou may copy a command from any HTR 8 key to any other. To copy a keyfunction, after entering the Learning Mode, and pressing the desired keyto be copied to, simply press the device key from which you wish to copy,having first pressed its Device Selector key if it resides on another “page.”The status LED will turn green; press the Device Selector key again to exitLearning Mode.Example: Copy the Pause command from the CD page to the AMP [ ]button:t On the HTR 8, simultaneously press-and-hold [AMP] and [RES]; the LearnLED turns steady green.t Press Pause [ ] ; the Learn LED turns amber.t Press [CD]; press Pause [ ] ; the Learn LED turns green.t Press [AMP] again to exit the learning mode.NOTEThe copy and punch-through functions are similar. However, if youcopy a command and then subsequently delete, or over-write theoriginal (source-key) command , the copied-to key’s command remainsunchanged. If you punch-through to a command and then delete orover-write the original key, the punched-through functions also changeaccordingly.MACRO COMMANDSA “macro” command is a series of two or more remote codes issuedautomatically from a single keypress. You might use a macro to automatea simple command sequence, such as, “Turn on the DVD player and thenpress PLAY”. Or you might compose an elaborate macro to power upan entire system, select a source, choose a Listening Mode, and beginplayback—again, all from a single keypress. The HTR 8 can store one macroon each of its function keys (these exclude the Device Selector keys).NOTEMacros are independent of the currently selected device.RECORDING MACROSTo record a macro, simultaneously press-and-hold for 3 seconds both the[MACRO] key and the HTR 8 function key to which you wish to assign themacro, until the status LED turns green. The macro button will also light up.Press the sequence of function keys to be recorded into the macro, beingsure to first press the requisite Device Selector key for each function (youmay switch devices while recording the macro as many times as necessary),allowing you to create macro containing commands from more than oneDevice Selector “page.”When you have finished entering the desired command sequence, press[MACRO] again to store the macro; the Learn LED and [MACRO] keyillumination will turn off.NOTEEach macro can store a maximum of 64 command steps. If you exceedthis number, the macro will be stored automatically after the 64thcommand is added.Example: Record a Macro to the [0] key to Turn on the T 187, Select“Input 1” (Source 1), and Commence Playback of connected Source 1 device(as in DVD player):t On the HTR 8, simultaneously press-and-hold [MACRO] and [0] (numericzero); the Learn LED turns steady green.t Press [AMP]; press [ON]; press [1] (“Input or Source 1”); press [DVD]; press[ ] (Play) - the Learn LED blinks as each step is added.t Press [MACRO] again to exit the macro-record mode.To clear a macro, perform the above steps without entering any functions.OPERATIONUSING THE HTR 8 REMOTE CONTROL40ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine