Crop H Position [0 to 1920]Make settings for the position in the horizontal direction for the cropframe specified in [Crop Adjust].0 is the left edge and 1920 is the right edge.This is only enabled when [UHD Crop] is set to [On].Crop V Position [0 to 1080]Make settings for the position in the vertical direction for the cropframe specified in [Crop Adjust].0 is the upper edge and 1080 is the lower edge.This is only enabled when [UHD Crop] is set to [On].ReturnReturn to the previous menu level. The CROP functionWhen [UHD Crop] is set to [On], it is possible to output images with FHDcropped from UHD signals from the 3G SDI OUT connector and IP.(Image 2)Video signals of UHD images down-converted to FHD are output tothe MONITOR OUT connector at this time, and the cropframe is displayed. (Image 1)Furthermore, UHD images are output from the 12G SDI OUT connector,SFP+ 14G FIBER connector, and HDMI connector, and the crop frameis not displayed.Crop frameImage 1 Image 2Depending on the [3G SDI/IP Out] and [Crop Out] settings, imagesoutput from the 3G SDI OUT connector and IP will be as shown below.3G SDI/IP Out Crop Out Images output from 3G SDI OUT connectorand IPFull – UHD images down-converted to FHDCrop YL Yellow frame FHD crop imagesG Green frame FHD crop imagesMG Magenta frame FHD crop imagesDepending on the [Crop Marker] setting, it is possible to select the cropframe output to the MONITOR OUT connector .Crop Marker Crop frame displayOff Crop frame is not displayed.YL Only a yellow crop frame is displayed.G Only a green crop frame is displayed.MG Only a magenta crop frame is displayed.YL+G Yellow and green crop frames are displayed.YL+MG Yellow and magenta crop frames are displayed.G+MG Green and magenta crop frames are displayed.YL+G+MG Yellow, green, and magenta crop frames are displayed.Pan/Tilt screenPan/TiltInstall Position DesktopSmart Picture Flip OffFlip Detect Angle 90degP/T Speed Mode NormalSpeed With Zoom Position OnFocus Adjust With PTZ. OffReturnInstall Position [Desktop, Hanging][Desktop] or [Hanging] is selected here as the method used to installthe unit.Desktop Stand-alone installationHanging Suspended installation• When [Hanging] has been selected, the top, bottom, left and rightof the images will be reversed, and up/down/left/right control forpanning and tilting will also be reversed.Smart Picture Flip [Off, Auto]When the tilt becomes the angle set for [Flip Detect Angle], the imagewill be flipped in the vertical direction automatically.Off The picture is not turned upside down.Auto The picture is automatically turned upside down.Flip Detect Angle [60deg to 120deg ]Set the tilt angle at which the image will be flipped in the verticaldirection automatically when [Smart Picture Flip] is set to [Auto].P/T Speed Mode [Normal, Fast]Set the speed of pan/tilt operation.Normal Pan/tilt operates at normal speed (maximum about 60° persecond).Fast Pan/tilt operates at fast speed (maximum about 200° persecond).• The pan/tilt operation noise may increase when [Fast] is selected.• Even when [Fast] is selected, the pan/tilt speed during presetplayback will be the same speed as when [Normal] is selected.Speed With Zoom Position [Off, On][Off] or [On] is set here for the function used to adjust the pan-tiltadjustment speed in conjunction with the zoom magnification.When [On] is set, the panning and tilting operations will becomeslower in the zoom status.This function has no effect during preset operations.Focus Adjust With PTZ. [Off, On][Off] or [On] is set here for the function which compensates for out-of-focusing when it occurs during panning, tilting or zooming operations.When [Off] is set, adjust the focus as required after zooming or set[Focus Mode] to [Auto].This is only enabled when [Manual] has been selected as the [FocusMode] setting.ReturnReturn to the previous menu level.60Camera menu items (continued)
