Yaesu FTDX-9000MP Operation Manual

Also see for FTDX-9000MP: Operation manual Brochure & specs Update guide Update guide Update guide

Page 146 FT DX 9000MP OPERATION MANUALMENU MODETUNING GROUP129. MAIN DIAL STEPFunction: Setting of the Main Tuning Knob’s tuningspeed on the SSB, CW, and AM modes.Available Values: 1 or 10 HzDefault Setting: 10 Hz130. MAIN DIAL CW FINEFunction: Setting of the Main Tuning Knob’s tuningspeed in the CW mode.Available Values: ENABLE/DISABLEDefault Setting: DISABLEENABLE :Tuning in 1 Hz steps on the CW mode.DISABLE: Tuning according to the steps determinedvia menu item 129: DIAL STEP.131. 1MHz/100kHz SELECTFunction: Selects the tuning steps for the CLAR/VFO-B knob when the BAND/MHz button is pressed.Available Values: 1 MHz/100 kHzDefault Setting: 1 MHz132. AM CH STEPFunction: Selects the tuning steps for themicrophone’s [UP]/[DWN] keys in the AM mode.Available Values: 2.5/5/9/10/12.5 kHzDefault Setting: 5 kHz133. FM CH STEPFunction: Selects the tuning steps for themicrophone’s [UP]/[DWN] keys in the FM mode.Available Values: 5/6.25/10/12.5/25 kHzDefault Setting: 5 kHz134. FM DIAL STEPFunction: Setting of the Main Tuning Knob’s tuningspeed in the FM mode.Available Values: 10/100 HzDefault Setting: 100 Hz135. MY BANDFunction: Programs a band to be skipped while se-lecting bands using the CLAR/VFO-B knob.Available Values: 1.8 ~ 50/GEN/TRVDefault Setting: TRVTo program the band to be skipped, rotate the CLAR/VFO-B knob to recall the band to be skipped whileselecting bands via the CLAR/VFO-B knob, then pressthe [ENT] key to change this setting to “ON.” Repeatthe same procedures to cancel the setting (skipped“off”). The skipped band will be high-lighted on the TFTdisplay.TX AUDIO GROUP136. F-PRMTRC EQ1-FREQFunction: Selects the center frequency of the lowerrange for the front panel’s parametric microphone equal-izer.Available Values: OFF/100 ~ 700 Hz (100 Hz/step)Default Setting: OFFOFF: The equalizer gain and Q-factor are set tofactory defaults (flat).100 ~ 700: You may adjust the equalizer gain and Q-factor at this selected audio frequency viamenu items 138: F-PRMTRC EQ1-LEVEL and 139: F-PRMTRC EQ1-BWTH.137. F-PRMTRC EQ1-LEVELFunction: Adjusts the equalizer gain of the low rangeof the front panel’s parametric microphone equalizer.Available Values: –10 ~ +10Default Setting: +5138. F-PRMTRC EQ1-BWTHFunction: Adjusts the Q-factor of the low range of thefront panel’s parametric microphone equalizer.Available Values: 1 ~ 10Default Setting: 10139. F-PRMTRC EQ2-FREQFunction: Selects the center frequency of the middlerange for the front panel’s parametric microphone equal-izer.Available Values: OFF/700 ~ 1500 Hz (100 Hz/step)Default Setting: OFFOFF: The equalizer gain and Q-factor are setto factory defaults (flat).700 ~ 1500: You may adjust the equalizer gain andQ-factor at this selected audio frequencyvia menu items 141: F-PRMTRC EQ2-LEVEL and 142: F-PRMTRC EQ2-BWTH.140. F-PRMTRC EQ2-LEVELFunction: Adjusts the equalizer gain of the middlerange of the front panel’s parametric microphone equal-izer.Available Values: –10 ~ +10Default Setting: +5141. F-PRMTRC EQ2-BWTHFunction: Adjusts the Q-factor of the middle range ofthe front panel’s parametric microphone equalizer.Available Values: 1 ~ 10Default Setting: 10